Author Topic: Full bridge showing half the voltage  (Read 5779 times)

Offline plasma

  • High Voltage Experimenter
  • **
  • Posts: 81
  • Karma: +0/-1
    • View Profile
Full bridge showing half the voltage
« on: November 30, 2019, 06:42:20 AM »
Hi I built this circuit, the diagram is just one leg, a inverteted signal is sent to the other leg. The Pwm and bridge share the same ground and 12V supply.
When measuring the output, I only get 6V, the problem has stumped me so I though to ask here.

Offline plasma

  • High Voltage Experimenter
  • **
  • Posts: 81
  • Karma: +0/-1
    • View Profile
Re: Full bridge showing half the voltage
« Reply #1 on: December 03, 2019, 07:29:48 AM »
Sorry the picture didn't come through.
The resistor at the top, pull up is 212ohms. The N MOSFET that triggers the others is switched with a hex Schmitt trigger, that produce one signal for one direction, and a invertered one for the other. The RC inverter brunches to one inverter, the other two, 58% duty cycle. Measuring on AC, the two outputs read 12V.

The problem is when I measure the voltage of the bridge with a DC blocking cap, to a bridge re iffer with a output cap it read 6V.

Offline klugesmith

  • High Voltage Senior
  • *****
  • Posts: 688
  • Karma: +22/-0
    • View Profile
Re: Full bridge showing half the voltage
« Reply #2 on: December 03, 2019, 07:41:00 PM »
The problem is when I measure the voltage of the bridge with a DC blocking cap, to a bridge re iffer with a output cap it read 6V.
We still need to guess what you are thinking. The quoted sentence, and paragraph before it, mention many components and connections not seen in your schematic. 

Things which seem obvious and skippable to you are, apparently, not so for many forum readers.  Slow down and draw.  The meter whose reading puzzles you is part of the circuit, so please show it.
« Last Edit: December 03, 2019, 07:42:53 PM by klugesmith »

Offline plasma

  • High Voltage Experimenter
  • **
  • Posts: 81
  • Karma: +0/-1
    • View Profile
Re: Full bridge showing half the voltage
« Reply #3 on: December 04, 2019, 12:11:32 AM »
This is the whole setup, thanks

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2744
  • Karma: +129/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: Full bridge showing half the voltage
« Reply #4 on: December 04, 2019, 04:26:38 AM »
If your new schematic is accurate, the bridge rectifier you are using to measure voltage is connected to the gate-drive on the right side rather than to the right-side H-Bridge output.
David Knierim

Offline klugesmith

  • High Voltage Senior
  • *****
  • Posts: 688
  • Karma: +22/-0
    • View Profile
Re: Full bridge showing half the voltage
« Reply #5 on: December 04, 2019, 07:41:21 AM »
Good catch, Dave.

Also: the bridge rectifier and capacitor circuit between DMM and probes looks like it should fairly replicate the DMM on AC-volts mode.
Without worries about the frequency response of DMM's true-RMS circuits fed with 50 kHz square waves.
But subject to: 
1. bridge rect diodes need to be fast enough
2. The DMM's DC-volts reading is 2 diode-drops smaller than voltage between the probes.

When those have been taken care of, what's the indicated AC voltage betwen the H-bridge outputs?
How about between one H-bridge output and ground?  Between the other H-bridge output and ground?  Between power and ground?

This seems to be an exercise in measuring mixed voltages (50 kHz AC on top of significant DC).
When you are satisfied with your AC-coupled rectfier, to look at the AC component of mixed voltages,
how about making a low-pass filter (R and C) for looking at the DC component of mixed voltages?
Like between the H-bridge outputs and each other, ground, and power?

Of course the DMM's internal AC and DC volts modes should take care of all that stuff, but apparently that's in question.

Last time I made a front-end circuit for DMM, was to measure variations in output current of an embedded buck converter running faster than 100 kHz.  12V in, 1.2 V out at around 15 amps.  Often the power distribution path in PC board can serve as a current sense resistor, but in this case it was a square shaped plane with 16 loads, fed in the center.  Wanted to monitor the voltage drop between 2 points having a single effective sense resistance, no matter how the current was distributed among the loads.  Had to use the buck converter's main inductor as the sense resistor.  Its average voltage drop, many tens of mV, is proportional to its DC current.  Successfully measured with DMM on mV scale, after a passive filter attenuated the high frequency 12 volt square wave which also appears between the probe points.
« Last Edit: December 04, 2019, 08:10:51 AM by klugesmith »

Offline plasma

  • High Voltage Experimenter
  • **
  • Posts: 81
  • Karma: +0/-1
    • View Profile
Re: Full bridge showing half the voltage
« Reply #6 on: December 04, 2019, 11:20:25 AM »
Made a low pass filter from 0 and 1 ohm and 2uF ,its only what I had on hand. The voltage through the recover dropped from 5.4V to 4V. Does that mean there is a lot or most is DC.
Running it through a transformer 1:2  works OK were each one out of four make 10V give or take?
Measuring with out the recifer AC is about 100mV and DC about the same.
Measuring from source to ground is around 11.5V

Offline shrad

  • High Voltage Experimenter
  • **
  • Posts: 54
  • Karma: +1/-0
    • View Profile
Re: Full bridge showing half the voltage
« Reply #7 on: December 04, 2019, 02:57:02 PM »
also, the rectifier bridge shows three diodes in a row, and one in reverse... if this is a typo don't mind my comment, but if it reflects real life circuit there will be an issue there also

Offline plasma

  • High Voltage Experimenter
  • **
  • Posts: 81
  • Karma: +0/-1
    • View Profile
Re: Full bridge showing half the voltage
« Reply #8 on: December 05, 2019, 11:38:59 PM »
Made a mistake, open circuit leads on the bridge, reading DC value from positive rail to ground, shows 3V.
From bridge leads to ground and positive rail, show around 1.4V AC setting and 1V DC.
Its a 2.5A supply and 212ohms for the gate rail , Must be a short! Tested with 11.6 ohm resistor just for the supply shows 11.5V.

Offline plasma

  • High Voltage Experimenter
  • **
  • Posts: 81
  • Karma: +0/-1
    • View Profile
Re: Full bridge showing half the voltage
« Reply #9 on: December 06, 2019, 05:19:26 AM »
Thanks for the help. I measure from drain to source on AC setting, all except the top right were 6-8V ,it was 0.1V replaced it and now get 15V from the recover part.

High Voltage Forum

Re: Full bridge showing half the voltage
« Reply #9 on: December 06, 2019, 05:19:26 AM »

 


* Recent Topics and Posts

post Re: Big Coil Build Log
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
Today at 05:47:34 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
davekni
Today at 04:45:07 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
Today at 04:18:27 AM
post Push Pull VTTC
[Vacuum Tube Tesla Coils (VTTC)]
janno288
Today at 01:10:08 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 27, 2024, 10:54:52 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 27, 2024, 11:53:42 AM
post Re: OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 05:14:36 AM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:47:48 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:41:59 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 27, 2024, 12:04:34 AM
post Re: Super flat QCW simulation (does this look reasonable?)
[Dual Resonant Solid State Tesla coils (DRSSTC)]
toooldforthis
March 26, 2024, 11:08:14 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 11:07:20 PM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 10:46:29 PM
post OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 26, 2024, 09:03:43 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 08:46:59 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 26, 2024, 05:02:18 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 03:16:03 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 26, 2024, 01:41:49 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 04:48:22 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 26, 2024, 04:16:37 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 26, 2024, 04:16:24 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 26, 2024, 04:13:02 AM
post Re: CM400 Induction Heater
[Electronic Circuits]
davekni
March 26, 2024, 04:00:43 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
davekni
March 26, 2024, 03:19:18 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
thedoc298
March 26, 2024, 01:50:42 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 08:05:02 PM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 25, 2024, 07:41:29 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 06:45:46 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 05:44:25 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 25, 2024, 04:47:17 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 04:27:22 PM
post Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 25, 2024, 03:57:34 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 25, 2024, 02:06:41 PM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 04:43:25 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
davekni
March 25, 2024, 02:39:40 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 12:47:09 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 24, 2024, 07:36:32 PM
post Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
Alberto
March 24, 2024, 07:27:24 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 24, 2024, 04:25:23 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 10:47:35 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 09:30:21 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 04:34:31 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 03:04:25 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 01:38:34 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 04:20:03 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 23, 2024, 12:54:30 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 23, 2024, 12:05:57 AM
post capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 22, 2024, 11:45:03 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 22, 2024, 11:30:09 PM
post Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 22, 2024, 10:20:35 PM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Benbmw
March 22, 2024, 09:21:13 PM
post Re: What actually kills MOSFETs?
[Beginners]
AstRii
March 22, 2024, 03:37:11 PM
post What actually kills MOSFETs?
[Beginners]
FPS
March 22, 2024, 05:09:20 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 22, 2024, 03:57:54 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 22, 2024, 02:59:25 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 06:31:42 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
rikkitikkitavi
March 21, 2024, 03:08:01 PM
post Re: [WTS] IGBT, Ferrite, Capacitors, Tools, PSU, Industrial components and parts
[Sell / Buy / Trade]
Mads Barnkob
March 21, 2024, 01:37:32 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Alberto
March 21, 2024, 11:42:07 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 21, 2024, 04:09:14 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 02:15:31 AM
post My Homemade Structural Analysis X-Ray Machine
[X-ray]
Luca c.
March 21, 2024, 01:35:40 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 20, 2024, 10:40:00 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Mads Barnkob
March 20, 2024, 08:03:41 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Mads Barnkob
March 20, 2024, 07:51:57 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 20, 2024, 10:39:47 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 20, 2024, 04:09:59 AM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 20, 2024, 01:13:23 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
March 20, 2024, 12:45:16 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 20, 2024, 12:30:30 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 11:12:24 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:47:49 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:44:19 PM
post Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 19, 2024, 06:52:09 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 19, 2024, 05:02:44 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
Mads Barnkob
March 19, 2024, 05:01:41 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 04:31:02 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 03:59:54 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 06:41:39 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 19, 2024, 04:05:49 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 18, 2024, 09:08:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 09:07:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
Twospoons
March 18, 2024, 08:57:06 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
MRMILSTAR
March 18, 2024, 03:51:33 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:59:46 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:33:25 PM
post Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 11:02:12 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Twospoons
March 18, 2024, 02:36:11 AM
post Re: Best forum for vacuum tube amplifiers?
[General Chat]
Mads Barnkob
March 17, 2024, 07:42:55 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:15:14 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 05:05:04 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
davekni
March 17, 2024, 04:50:51 AM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Twospoons
March 17, 2024, 04:45:17 AM
post 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:17:51 AM
post Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Terry
March 17, 2024, 01:29:32 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 17, 2024, 12:33:06 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
March 16, 2024, 08:46:20 PM
post Re: Bleeder resistor for MMC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hydron
March 16, 2024, 08:39:24 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hydron
March 16, 2024, 08:21:44 PM
post Best forum for vacuum tube amplifiers?
[General Chat]
yourboi
March 16, 2024, 08:20:13 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal