Author Topic: primary coil support  (Read 668 times)

Offline DaiKen

  • High Voltage Enthusiast
  • *
  • Posts: 31
  • Karma: +0/-0
    • View Profile
primary coil support
« on: February 10, 2018, 08:20:05 PM »
Hi all,

In http://kaizerpowerelectronics.dk/tesla-coils/kaizer-drsstc-i/ Mads writes: 'I do not recommend anyone to make the same primary coil supports' and I have some trouble finding a working alternative.

Suggestions, advice & tips are very welcome.

Kind regards,

Ton

Offline Mads Barnkob

  • Administrator
  • High Voltage Senior
  • *****
  • Posts: 825
  • Karma: +6/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: primary coil support
« Reply #1 on: February 11, 2018, 07:26:16 PM »
What I meant was the through-hole solution, because it is very hard work to get it screwed into position.

You can do almost exactly the same, but then saw down through the holes, just a little off centre so you get a little snap-in to hold the tubing in place, or you can also drill small holes behind the slots to fix the coil into position with a small piece of wire or so. Take a look at my DRSSTC4 f.ex.

But I do recommend make flat spiral primary coils for DRSSTCs, they provide plenty of coupling and gets further away from the topload.
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline DaiKen

  • High Voltage Enthusiast
  • *
  • Posts: 31
  • Karma: +0/-0
    • View Profile
Re: primary coil support
« Reply #2 on: February 11, 2018, 08:15:10 PM »
Hi Mads,

Thanks for your reply. That's just what I read, and looking at the pictures I can imaging the difficulties.

Making a flat spiral coil for a coil based on your DRSSTC1, can I use the same amount of windings?

Offline Mads Barnkob

  • Administrator
  • High Voltage Senior
  • *****
  • Posts: 825
  • Karma: +6/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: primary coil support
« Reply #3 on: February 11, 2018, 10:24:31 PM »
You don't even need so many turns, as it will be tapped at a much lower number of turns, in the range of 5-6 turns in order to de-tune the primary below secondary resonant frequency.

On http://kaizerpowerelectronics.dk/calculators/spiral-coil-calculator/ I plotted these numbers and that seems to be a good enough solution for DRSSTC1, you can change the distance between turns if its getting too big, but too small also makes it harder to tune with a large tap connection.

http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline DaiKen

  • High Voltage Enthusiast
  • *
  • Posts: 31
  • Karma: +0/-0
    • View Profile
Re: primary coil support
« Reply #4 on: February 12, 2018, 03:44:13 PM »
Thanks Mad!

Like it very much you took the effort to make this calculation!

High Voltage Forum

Re: primary coil support
« Reply #4 on: February 12, 2018, 03:44:13 PM »

 


* Recent Topics and Posts

post Re: TO-247 IGBT Comparison for High Frequency & Paralleled Operation
[Dual Resonant Solid State Tesla coils]
Laci
Today at 10:30:34 PM
post Re: TO-247 IGBT Comparison for High Frequency & Paralleled Operation
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
Today at 09:42:25 PM
post Re: TO-247 IGBT Comparison for High Frequency & Paralleled Operation
[Dual Resonant Solid State Tesla coils]
Laci
Today at 09:25:26 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
Today at 12:50:45 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
Today at 10:45:01 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
Today at 09:47:51 AM
post Re: TO-247 IGBT Comparison for High Frequency & Paralleled Operation
[Dual Resonant Solid State Tesla coils]
sjsimmo
Today at 03:18:05 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
Today at 02:08:57 AM
post Re: TO-247 IGBT Comparison for High Frequency & Paralleled Operation
[Dual Resonant Solid State Tesla coils]
Fumeaux
December 17, 2018, 10:22:31 PM
post TO-247 IGBT Comparison for High Frequency & Paralleled Operation
[Dual Resonant Solid State Tesla coils]
Laci
December 17, 2018, 09:36:03 PM
post Re: spectral analysis of Tesla coils
[Spark gap Tesla coils]
Mads Barnkob
December 17, 2018, 02:20:01 PM
post Re: DRSSTC design guide - progress report
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 17, 2018, 01:13:34 PM
post Re: spectral analysis of Tesla coils
[Spark gap Tesla coils]
Uspring
December 17, 2018, 01:02:35 PM
post Re: DRSSTC design guide - progress report
[Dual Resonant Solid State Tesla coils]
Uspring
December 17, 2018, 12:33:07 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 17, 2018, 12:26:08 PM
post Re: Building of my first tesla coil
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 17, 2018, 10:42:17 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 17, 2018, 06:49:52 AM
post Re: Building of my first tesla coil
[Dual Resonant Solid State Tesla coils]
Skylex86
December 16, 2018, 09:09:13 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
Mads Barnkob
December 16, 2018, 07:48:55 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
NordicGaben
December 16, 2018, 06:13:54 PM
post spectral analysis of Tesla coils
[Spark gap Tesla coils]
Physikfan
December 15, 2018, 02:24:20 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
DashApple
December 14, 2018, 10:21:25 PM
post Re: DRSSTC design guide - progress report
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 14, 2018, 08:38:52 PM
post Re: DRSSTC design guide - progress report
[Dual Resonant Solid State Tesla coils]
Uspring
December 13, 2018, 12:23:30 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 12, 2018, 11:57:02 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 12, 2018, 01:15:30 PM
post Re: DRSSTC design guide - progress report
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 12, 2018, 01:00:34 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 12, 2018, 11:45:08 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 11, 2018, 09:13:49 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 11, 2018, 12:03:54 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 10, 2018, 12:25:15 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 10, 2018, 11:13:38 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 10, 2018, 09:18:24 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Mads Barnkob
December 10, 2018, 09:13:37 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 10, 2018, 02:18:59 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
sjsimmo
December 09, 2018, 11:09:34 PM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Fumeaux
December 09, 2018, 10:23:38 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 09, 2018, 06:05:02 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Jesjes
December 09, 2018, 04:50:56 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Laci
December 08, 2018, 12:52:41 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 08, 2018, 09:51:47 AM
post Huawei RRU3928 1800MHz radio base station teardown (part 1 of 2)
[Radio frequency]
Mads Barnkob
December 06, 2018, 07:49:06 PM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Fumeaux
December 03, 2018, 10:35:13 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
sjsimmo
December 03, 2018, 08:40:43 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Jesjes
December 03, 2018, 05:31:29 AM
post Re: Hacking the IKEA 2000 Watt induction stove (5 parts)
[Electronic circuits]
chjarup
December 02, 2018, 11:44:14 PM
post SSTC-Driver PCB 1.3
[Printed Circuit Board]
Fumeaux
December 02, 2018, 10:25:23 PM
post Re: Hacking the IKEA 2000 Watt induction stove (5 parts)
[Electronic circuits]
Mads Barnkob
December 02, 2018, 04:23:16 PM
post Re: Hacking the IKEA 2000 Watt induction stove (5 parts)
[Electronic circuits]
chjarup
December 02, 2018, 12:12:57 PM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Mads Barnkob
December 02, 2018, 09:57:04 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30