This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Topics - Max Seiringer
Pages: [1]
1
« on: January 08, 2022, 03:21:31 PM »
Hi folks! I'm buildung a small solid state teslacoil using a 74HC14 feedbacksystem with a current transformer. First off some detail: The circuit diagram is pretty similar to the Kaizer SSTC II. I am driving my coil with a IRFP460 fullbridge at 30VDC at the moment. Sadly, there is currently no safe way to conduct tests at higher voltages, the variac is out of order. I use a sheet of aluminum foil as an earth plane, since i live in a small apartment and no proper ground is available. The cores used for the GDT and the CT are 3E25 and N30. The primary coil features 8 windings and the secondary coil just above 1000 turns. The resonant frequency is about 270kHz. The Interrupter is based on an Arduino Micro and has audio capabilities. It is connected to the driver logic via a fiber obtic cable. The setup works to some extend. The arcs come in at about 1cm at 30VDC while drawing roughly 3A in CW mode. Not too great results considering the coil is driven by a fullbridge. I measured across the primary with one probe and used a second probe as an antenna to pick up the signal from the secondary. It seems that the voltage across the primary coil leads the voltage at the secondary. This results in a 60° phase angle between the two signals. What phase angle would be ideal for a solid state teslacoil? Could the performance issues be fixed by adding phase compensation to the circuit or is there another culprit? Kind regards Max
2
« on: April 12, 2020, 09:54:27 PM »
Hey there! I am building the Kaizer SSTC1 as my first SSTC project and I ran into some issues. First off, I based the circiut around the schematics given from http://kaizerpowerelectronics.dk/tesla-coils/kaizer-sstc-i/]http://kaizerpowerelectronics.dk/tesla-coils/kaizer-sstc-i/. I only changed one thing: I didn't have a UCC37322 IC, so I used two UCC37321 and inverted the input-signal for one of those two drivers with the help of a spare input of the 74HC14 IC. I currently use two lab-supplies for powering the electronics and the coil itsels seperately. Later on, one supply should be replaced with the variac. The coil has its resonant frequency at 210kHz. 1) When running on low voltage (10V) the circuit works rather good. The only issue is a small spike at the rising edge of the gate-signal. When increasing the input voltage up to 30V, the spike grows and the gate-signal gets very noisy and unclean. At a certain point (above 40V) the frequency jumps to about 600kHz and the supplies go into current limitation. The only way to get the system back to its resonant frequency is to shut it down completely. The radiated field picked up form the probe of the oscilloscope looks fine, until a certain input-voltage. A significant amount of noise is noticeable at about 30V input. May this voltage dependent spike have to do something with the Miller-Effect? I checked the GDT with my function generator, the signal looks perfect even with the MOSFETS connected, but without any load connected. The issues only occur when the bridge is connected to the driver. Another thing I considered is grounding, I tried different methods of connecting the coil to earth with the same results. 2) I have issues when trying to interrupt the circuit. I tired to tie the enable-pins of the UCC37321 ICs directly to ground but the circuit keeps oscillating like usually, no matter what I try. The voltage at the ICs is rather smooth and free from any noise, only very small ripples are noticeable at the voltage-supply for the 74HC14 IC. What could be the cause of this problem? Please excuse my english, I'm still learning Kind reguards, Max Seiringer
Pages: [1]
Recent Topics and Posts
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
MRMILSTAR Today at 05:24:19 AM
|
|
Re: Difference between these transformers
[Transformer (Ferrite Core)]
|
Tesla Junior Today at 04:24:09 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ Today at 04:20:35 AM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
Bobakman Today at 04:05:28 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
alan sailer Today at 04:03:54 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ Today at 03:19:19 AM
|
|
Re: IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
davekni Today at 03:09:29 AM
|
|
Re: IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
unrealcrafter2 Today at 01:47:37 AM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
Bobakman Today at 12:19:21 AM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
klugesmith April 18, 2024, 11:33:01 PM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
Bobakman April 18, 2024, 11:15:15 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
davekni April 18, 2024, 10:59:36 PM
|
|
Re: What actually kills MOSFETs?
[Beginners]
|
unrealcrafter2 April 18, 2024, 10:03:48 PM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
klugesmith April 18, 2024, 09:53:25 PM
|
|
Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
|
unrealcrafter2 April 18, 2024, 09:50:09 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 18, 2024, 09:15:55 PM
|
|
Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Mads Barnkob April 18, 2024, 08:50:49 PM
|
|
Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
unrealcrafter2 April 18, 2024, 08:11:27 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
davekni April 18, 2024, 07:28:05 PM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
Bobakman April 18, 2024, 06:30:30 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 18, 2024, 06:03:57 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 18, 2024, 05:26:13 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
NyaaX_X April 18, 2024, 04:03:38 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 18, 2024, 02:56:40 PM
|
|
Re: DIY induction guns? (warning:long)
[Induction Launchers, Coil Guns and Rails guns]
|
Benbmw April 18, 2024, 06:17:15 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 18, 2024, 05:46:07 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
MRMILSTAR April 18, 2024, 05:18:31 AM
|
|
Re: IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
davekni April 18, 2024, 04:34:52 AM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
klugesmith April 18, 2024, 04:11:53 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 18, 2024, 04:02:44 AM
|
|
Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
davekni April 18, 2024, 03:35:52 AM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
MRMILSTAR April 17, 2024, 11:54:05 PM
|
|
100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Benjamin Lockhart April 17, 2024, 11:37:16 PM
|
|
Re: Has anyone tried to build a TMT (extra coil) Tesla coil?
[General Chat]
|
Michelle_ April 17, 2024, 02:29:30 AM
|
|
Re: Has anyone tried to build a TMT (extra coil) Tesla coil?
[General Chat]
|
MRMILSTAR April 16, 2024, 11:56:12 PM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
klugesmith April 16, 2024, 11:46:57 PM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
Bobakman April 16, 2024, 10:40:11 PM
|
|
Has anyone tried to build a TMT (extra coil) Tesla coil?
[General Chat]
|
Michelle_ April 16, 2024, 09:21:39 PM
|
|
Re: Medium Drsstc question
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
flyingperson23 April 16, 2024, 08:04:16 PM
|
|
Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Benjamin Lockhart April 16, 2024, 06:48:05 PM
|
|
Re: Game changing tesla coil secondary winding suggestions
[General Chat]
|
Michelle_ April 16, 2024, 06:18:40 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 16, 2024, 06:14:53 PM
|
|
Re: 3D printed mini-slayer: world's weakest tesla coil
[Solid State Tesla Coils (SSTC)]
|
unrealcrafter2 April 16, 2024, 05:44:44 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
MRMILSTAR April 16, 2024, 03:12:12 PM
|
|
Re: Drsstc voltage spike question
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
unrealcrafter2 April 16, 2024, 02:28:01 PM
|
|
Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Saattvik24 April 16, 2024, 01:56:26 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 16, 2024, 06:50:47 AM
|
|
Re: IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Anders Mikkelsen April 16, 2024, 04:57:47 AM
|
|
Re: IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
ethanwu0131 April 16, 2024, 03:40:53 AM
|
|
Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
flyingperson23 April 16, 2024, 01:31:17 AM
|
|
Re: Game changing tesla coil secondary winding suggestions
[General Chat]
|
Michelle_ April 15, 2024, 11:19:52 PM
|
|
3D printed mini-slayer: world's weakest tesla coil
[Solid State Tesla Coils (SSTC)]
|
Michelle_ April 15, 2024, 11:10:19 PM
|
|
Re: Game changing tesla coil secondary winding suggestions
[General Chat]
|
alan sailer April 15, 2024, 11:04:19 PM
|
|
Re: Ignitron trigger drive ideas?
[Capacitor Banks]
|
Twospoons April 15, 2024, 11:02:05 PM
|
|
Re: Game changing tesla coil secondary winding suggestions
[General Chat]
|
Michelle_ April 15, 2024, 10:57:59 PM
|
|
Re: Game changing tesla coil secondary winding suggestions
[General Chat]
|
Michelle_ April 15, 2024, 10:55:46 PM
|
|
Re: Return of Electronics Flea Market in "Silicon Valley"
[Sell / Buy / Trade]
|
klugesmith April 15, 2024, 10:37:32 PM
|
|
Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Saattvik24 April 15, 2024, 10:05:00 PM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
MRMILSTAR April 15, 2024, 09:28:50 PM
|
|
Ignitron trigger drive ideas?
[Capacitor Banks]
|
klugesmith April 15, 2024, 09:06:42 PM
|
|
Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Mads Barnkob April 15, 2024, 08:46:32 PM
|
|
Re: Game changing tesla coil secondary winding suggestions
[General Chat]
|
Benbmw April 15, 2024, 08:38:39 PM
|
|
Re: Game changing tesla coil secondary winding suggestions
[General Chat]
|
sky-guided April 15, 2024, 08:23:40 PM
|
|
How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
Bobakman April 15, 2024, 06:43:23 PM
|
|
Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
flyingperson23 April 15, 2024, 06:29:10 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 15, 2024, 05:21:53 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 15, 2024, 05:15:33 AM
|
|
Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
davekni April 15, 2024, 04:07:54 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
davekni April 15, 2024, 03:49:03 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
alan sailer April 14, 2024, 09:46:30 PM
|
|
Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 14, 2024, 07:31:00 PM
|
|
Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Saattvik24 April 14, 2024, 02:26:19 PM
|
|
Re: mg75q2ys40 IGBT
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Mads Barnkob April 14, 2024, 07:20:54 AM
|
|
Re: IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Mads Barnkob April 14, 2024, 07:18:20 AM
|
|
Re: Game changing tesla coil secondary winding suggestions
[General Chat]
|
Michelle_ April 13, 2024, 06:46:40 AM
|
|
Re: Game changing tesla coil secondary winding suggestions
[General Chat]
|
Michelle_ April 13, 2024, 04:18:42 AM
|
|
Re: Upper and Lower Explosive Limits on Confined Flammable Vapors at -79 C.
[General Chat]
|
alan sailer April 13, 2024, 03:24:20 AM
|
|
Re: Game changing tesla coil secondary winding suggestions
[General Chat]
|
alan sailer April 13, 2024, 03:20:46 AM
|
|
Game changing tesla coil secondary winding suggestions
[General Chat]
|
Michelle_ April 13, 2024, 03:13:22 AM
|
|
Re: Capacitor Blowout
[Sell / Buy / Trade]
|
lbattraw April 12, 2024, 09:14:58 PM
|
|
mg75q2ys40 IGBT
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
thedark April 12, 2024, 08:40:18 PM
|
|
Re: UD 2.7 OCD LED stays on, no output during inital test
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
davekni April 12, 2024, 07:20:30 PM
|
|
Re: Mosfet Buffer Stage Questions
[Beginners]
|
davekni April 12, 2024, 07:12:43 PM
|
|
IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
ethanwu0131 April 12, 2024, 04:47:33 PM
|
|
Re: UD 2.7 OCD LED stays on, no output during inital test
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Admiral Aaron Ravensdale April 12, 2024, 11:43:36 AM
|
|
Mosfet Buffer Stage Questions
[Beginners]
|
Egg April 12, 2024, 12:49:02 AM
|
|
Re: UD 2.7 OCD LED stays on, no output during inital test
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
davekni April 12, 2024, 12:41:16 AM
|
|
Re: Plasma Torid - Class E Self Resonant Dual/Stereo - Plasma Torid Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
davekni April 12, 2024, 12:22:41 AM
|
|
Re: Capacitor Blowout
[Sell / Buy / Trade]
|
Michelle_ April 11, 2024, 10:45:53 PM
|
|
Re: UD 2.7 OCD LED stays on, no output during inital test
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Admiral Aaron Ravensdale April 11, 2024, 07:39:30 PM
|
|
Re: UD 2.7 OCD LED stays on, no output during inital test
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
flyingperson23 April 11, 2024, 07:24:52 PM
|
|
Re: Tesla coil safety questions, risk analysis quantified
[Beginners]
|
sky-guided April 11, 2024, 06:09:30 PM
|
|
UD 2.7 OCD LED stays on, no output during inital test
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Admiral Aaron Ravensdale April 11, 2024, 12:55:16 PM
|
|
Re: Plasma Torid - Class E Self Resonant Dual/Stereo - Plasma Torid Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
alan sailer April 11, 2024, 03:40:00 AM
|
|
Re: Plasma Torid - Class E Self Resonant Dual/Stereo - Plasma Torid Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
sky-guided April 11, 2024, 03:05:07 AM
|
|
Re: Tesla coil safety questions, risk analysis quantified
[Beginners]
|
Michelle_ April 11, 2024, 02:57:33 AM
|
|
Re: Tesla coil safety questions, risk analysis quantified
[Beginners]
|
alan sailer April 11, 2024, 01:44:32 AM
|
|
Re: Tesla coil safety questions, risk analysis quantified
[Beginners]
|
Michelle_ April 11, 2024, 01:31:40 AM
|
|
Re: Plasma Torid - Class E Self Resonant Dual/Stereo - Plasma Torid Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
OmGigaTron April 11, 2024, 01:11:00 AM
|
|
Re: Tesla coil safety questions, risk analysis quantified
[Beginners]
|
alan sailer April 11, 2024, 12:58:52 AM
|
|