This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - justin66
Pages: [1]
1
« on: December 07, 2020, 04:16:51 PM »
2
« on: December 07, 2020, 04:14:45 PM »
i have read about the chinise 1200v caps for induction cookers 0.33uf is a nice cap to use. now i will test them with more power as soon as i can figure out my problems with the bridge. the dawn caps i have seen and they should be good ones as well.
3
« on: February 01, 2020, 12:00:11 PM »
The 1200V 0.33uF induction cooker capacitors have worked quite well for me. I don't use them above 1200V peak (+-1200V sine wave) in my DRSSTC. I've abuse-tested a couple parts in simulated DRSSTC use (1% duty cycle bursts of 80kHz). At +-1700V, they lasted a week continuous with no significant changes (no leakage current increase or capacitance decrease). Tested the same parts for two more days at +-2000V, then finally fried them at +-2150V. So, you might get away with +-1700V. On the other hand, the two parts I tested to destruction may have been lucky. With a large array, the weakest part drives maximum voltage. That's why I stay <=1200V for actual DRSSTC use.
As long as you parallel three identical IGBT half-bridge parts for one side of the full-bridge, and the other three identical parts for the other half-bridge, I think you'll be OK. The biggest difference I noticed in the spec. sheets is the typical current vs. gate-voltage curves. One has significantly lower Vge for a given current. Make sure your gate-drive is at least +-15V (or a bit more) to properly drive the higher-Vge part.
Thanks for reply. How do i calculate maximum voltage on my resonant circuit? I believe its dependent on the PW so im not sure how to measure or limit the maximum voltage. I have seen guys at kaizerelectronics make mmc with maximum of 4kvdc and provide a great results in terms of sparks. Im using UD 2.7 so gdt 1:1 should provide somewhere close to 24v of drive voltage so i think im good on that part. The problem is that there will always be different igbts conducting in any given time because it conducts in an x patern. Im still not sure about the maximum amperage that i can safely push igbts, maybe i dont need to use so much igbts? I have seen small to247 igbts capable of 200A in a zvs and only have 20A hard swich current so maybe 150A igbts can do 1.5kA? I cant find a compatible industrial fiberoptics pair that can for sure talk to each other, what transmitter do you guys use for if-d95t to properly read signals?
4
« on: February 01, 2020, 12:49:26 AM »
hello guys, im very inexperienced in making DRSSTCs so i would like your opinion about my plans, it is my second DRSSTC first got about 20cm sparks with 40cm winding quite dissapointing considering 180a OCD it had 1000 turns... now i have 1200v igbts that are rated 150A continuous i want about 600-900A primary current. so i got some igbts from a motor controller and i wonder if it would be safe to run similar but not identical igbts for a dual or tripple paralel full bridge configuration? and what about an overdrive there is no info about ZVS operation how far should i push my IGBTs ? can you guys with more experience tell me if this would be a good configuration in terms of chosen wire size using javatc there is no indication what is good or not. my goal is 2 meter sparks, more is always better as long as secondary can handle it. also the MMC im not sure about how much DCV i need to make it robust? i will use chineyseum induction cooker caps, i have read they are good for MMCs and also cheap the GDT is one enough or i need to make more than one for more current? i have seen people disabling OCP but where do i find info about my own IGBTs? black bricks have OCP what is compatible IF-D95T transmitter part? because IF-E96E doesnt work datasheets https://www.fujielectric-europe.com/downloads/2MBI150VB-120-50_1734942.PDFhttp://www.ic72.com/pdf_file/2/58778.pdf
5
« on: January 24, 2020, 04:15:41 PM »
The OCD at turn-on thing with the UD2.7 is caused by the UVLO IC. This design isn't the best (the UVLO stops working at very low voltages as it was just a quick hack based on what I had on hand at the time I implemented it, after which it was copied and added to the UD2.7 design), so I wouldn't sweat it as long as the driver actually works.
thanks for replying, i found the pesky problem, there is JP1 and JP2 jumper point that i totally forgot to install and short out after installing jumper near 9v buck regulator the ocd led turns on if i jump those, so i think its the one that turns on UVLO.
6
« on: January 24, 2020, 11:43:08 AM »
thanks Mads, i appreciate your work and answer. i will try fitting ST, hope its going to sort out, have a nice day.
7
« on: January 23, 2020, 11:15:12 PM »
The UD2.7C will light the power and OCD LEDs on power up until it receives feedback and an interrupter signal.
For testing without a proper interrupter, I've found a bright white LED flashlight will work in a pinch, shined directly into the ST fiber receiver.
It sounds like you have a problem with the board that always lights the signal LED sounds. That shouldn't happen. I'd double check you don't have any cold solder joints or bridged joints. Beyond that, I'd have to sit down and stare at the schematic for a few minutes to guess where the problem could be. Perhaps others will chime in.
Good news is it sounds like you have one good board. You can use that with your DMM and scope to compare against.
the driver works every way i test it but the OCD LED doesnt turn on when powered with out interupter.
8
« on: January 23, 2020, 07:48:39 PM »
[deleted irrelevant information] basically when powering UD2.7c the OCD and power led should be present. in my case OCD LED doesnt turn on. it only turns on when tripped. is it something to worry about?
Pages: [1]
Recent Topics and Posts
|
Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
|
MRMILSTAR Today at 04:47:35 AM
|
|
Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
|
davekni Today at 03:59:27 AM
|
|
Re: Kaizer VTTC 1
[Vacuum Tube Tesla Coils (VTTC)]
|
MRMILSTAR March 28, 2024, 09:15:11 PM
|
|
Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
|
Alberto March 28, 2024, 01:01:12 PM
|
|
Re: Big Coil Build Log
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
flyingperson23 March 28, 2024, 05:47:34 AM
|
|
Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
|
davekni March 28, 2024, 04:45:07 AM
|
|
Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
|
MRMILSTAR March 28, 2024, 04:18:27 AM
|
|
Push Pull VTTC
[Vacuum Tube Tesla Coils (VTTC)]
|
janno288 March 28, 2024, 01:10:08 AM
|
|
Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
|
Alberto March 27, 2024, 10:54:52 PM
|
|
Re: CM400 Induction Heater
[Electronic Circuits]
|
markus March 27, 2024, 11:53:42 AM
|
|
Re: OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
davekni March 27, 2024, 05:14:36 AM
|
|
Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
davekni March 27, 2024, 04:47:48 AM
|
|
Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
davekni March 27, 2024, 04:41:59 AM
|
|
Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
alan sailer March 27, 2024, 12:04:34 AM
|
|
Re: Super flat QCW simulation (does this look reasonable?)
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
toooldforthis March 26, 2024, 11:08:14 PM
|
|
Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Benjamin Lockhart March 26, 2024, 11:07:20 PM
|
|
Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Benjamin Lockhart March 26, 2024, 10:46:29 PM
|
|
OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Saattvik24 March 26, 2024, 09:03:43 PM
|
|
Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
alan sailer March 26, 2024, 08:46:59 PM
|
|
Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
flyingperson23 March 26, 2024, 05:02:18 PM
|
|
Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
alan sailer March 26, 2024, 03:16:03 PM
|
|
Re: CM400 Induction Heater
[Electronic Circuits]
|
Anders Mikkelsen March 26, 2024, 01:41:49 PM
|
|
Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Benjamin Lockhart March 26, 2024, 04:48:22 AM
|
|
Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
|
MRMILSTAR March 26, 2024, 04:16:37 AM
|
|
Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
davekni March 26, 2024, 04:16:24 AM
|
|
Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
|
davekni March 26, 2024, 04:13:02 AM
|
|
Re: CM400 Induction Heater
[Electronic Circuits]
|
davekni March 26, 2024, 04:00:43 AM
|
|
Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
|
davekni March 26, 2024, 03:19:18 AM
|
|
Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
thedoc298 March 26, 2024, 01:50:42 AM
|
|
Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
flyingperson23 March 25, 2024, 08:05:02 PM
|
|
Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
|
Mads Barnkob March 25, 2024, 07:41:29 PM
|
|
Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
alan sailer March 25, 2024, 06:45:46 PM
|
|
Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
flyingperson23 March 25, 2024, 05:44:25 PM
|
|
Re: CM400 Induction Heater
[Electronic Circuits]
|
Anders Mikkelsen March 25, 2024, 04:47:17 PM
|
|
Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
alan sailer March 25, 2024, 04:27:22 PM
|
|
Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
|
MRMILSTAR March 25, 2024, 03:57:34 PM
|
|
Re: CM400 Induction Heater
[Electronic Circuits]
|
markus March 25, 2024, 02:06:41 PM
|
|
Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
|
KrisPringle March 25, 2024, 04:43:25 AM
|
|
Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
|
davekni March 25, 2024, 02:39:40 AM
|
|
Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
|
KrisPringle March 25, 2024, 12:47:09 AM
|
|
Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
|
Alberto March 24, 2024, 07:36:32 PM
|
|
Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
|
Alberto March 24, 2024, 07:27:24 PM
|
|
Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
|
MRMILSTAR March 24, 2024, 04:25:23 AM
|
|
Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
|
Alberto March 23, 2024, 10:47:35 PM
|
|
Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
|
MRMILSTAR March 23, 2024, 09:30:21 PM
|
|
Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
|
Alberto March 23, 2024, 04:34:31 PM
|
|
Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
|
MRMILSTAR March 23, 2024, 03:04:25 PM
|
|
Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
|
Alberto March 23, 2024, 01:38:34 PM
|
|
Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
|
MRMILSTAR March 23, 2024, 04:20:03 AM
|
|
Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
|
davekni March 23, 2024, 12:54:30 AM
|
|
Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
|
davekni March 23, 2024, 12:05:57 AM
|
|
capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
|
Alberto March 22, 2024, 11:45:03 PM
|
|
Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
|
OmGigaTron March 22, 2024, 11:30:09 PM
|
|
Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
|
Mads Barnkob March 22, 2024, 10:20:35 PM
|
|
Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
|
Benbmw March 22, 2024, 09:21:13 PM
|
|
Re: What actually kills MOSFETs?
[Beginners]
|
AstRii March 22, 2024, 03:37:11 PM
|
|
What actually kills MOSFETs?
[Beginners]
|
FPS March 22, 2024, 05:09:20 AM
|
|
Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Benjamin Lockhart March 22, 2024, 03:57:54 AM
|
|
Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
davekni March 22, 2024, 02:59:25 AM
|
|
Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Benjamin Lockhart March 21, 2024, 06:31:42 PM
|
|
Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
|
rikkitikkitavi March 21, 2024, 03:08:01 PM
|
|
Re: [WTS] IGBT, Ferrite, Capacitors, Tools, PSU, Industrial components and parts
[Sell / Buy / Trade]
|
Mads Barnkob March 21, 2024, 01:37:32 PM
|
|
Re: Difference between these transformers
[Transformer (Ferrite Core)]
|
Alberto March 21, 2024, 11:42:07 AM
|
|
Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
davekni March 21, 2024, 04:09:14 AM
|
|
Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Benjamin Lockhart March 21, 2024, 02:15:31 AM
|
|
My Homemade Structural Analysis X-Ray Machine
[X-ray]
|
Luca c. March 21, 2024, 01:35:40 AM
|
|
Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Saattvik24 March 20, 2024, 10:40:00 PM
|
|
Re: Difference between these transformers
[Transformer (Ferrite Core)]
|
Mads Barnkob March 20, 2024, 08:03:41 PM
|
|
Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
|
Mads Barnkob March 20, 2024, 07:51:57 PM
|
|
Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Mads Barnkob March 20, 2024, 10:39:47 AM
|
|
Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
davekni March 20, 2024, 04:09:59 AM
|
|
Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Benjamin Lockhart March 20, 2024, 01:13:23 AM
|
|
Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Keybored March 20, 2024, 12:45:16 AM
|
|
Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
flyingperson23 March 20, 2024, 12:30:30 AM
|
|
Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Benjamin Lockhart March 19, 2024, 11:12:24 PM
|
|
Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Late March 19, 2024, 09:47:49 PM
|
|
Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Late March 19, 2024, 09:44:19 PM
|
|
Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Saattvik24 March 19, 2024, 06:52:09 PM
|
|
Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
flyingperson23 March 19, 2024, 05:02:44 PM
|
|
Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
|
Mads Barnkob March 19, 2024, 05:01:41 PM
|
|
Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Mads Barnkob March 19, 2024, 04:31:02 PM
|
|
Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Mads Barnkob March 19, 2024, 03:59:54 PM
|
|
Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Benjamin Lockhart March 19, 2024, 06:41:39 AM
|
|
Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
|
davekni March 19, 2024, 04:05:49 AM
|
|
Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
|
OmGigaTron March 18, 2024, 09:08:35 PM
|
|
Re: Can I Trust This Super Cheap Site?
[General Chat]
|
2020-Man March 18, 2024, 09:07:35 PM
|
|
Re: Can I Trust This Super Cheap Site?
[General Chat]
|
Twospoons March 18, 2024, 08:57:06 PM
|
|
Re: Can I Trust This Super Cheap Site?
[General Chat]
|
MRMILSTAR March 18, 2024, 03:51:33 PM
|
|
Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Late March 18, 2024, 02:59:46 PM
|
|
Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Late March 18, 2024, 02:33:25 PM
|
|
Can I Trust This Super Cheap Site?
[General Chat]
|
2020-Man March 18, 2024, 11:02:12 AM
|
|
Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
|
Twospoons March 18, 2024, 02:36:11 AM
|
|
Re: Best forum for vacuum tube amplifiers?
[General Chat]
|
Mads Barnkob March 17, 2024, 07:42:55 PM
|
|
Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
|
Michelle_ March 17, 2024, 04:15:14 PM
|
|
Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
|
Michelle_ March 17, 2024, 05:05:04 AM
|
|
Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
|
davekni March 17, 2024, 04:50:51 AM
|
|
Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
|
Twospoons March 17, 2024, 04:45:17 AM
|
|
2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
|
Michelle_ March 17, 2024, 04:17:51 AM
|
|
Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
|
Terry March 17, 2024, 01:29:32 AM
|
|
Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
flyingperson23 March 17, 2024, 12:33:06 AM
|
|