Author Topic: WTS/WTT: T520-2 - Micrometals core, MO, USA  (Read 3292 times)

Offline coilerer

  • High Voltage Enthusiast
  • *
  • Posts: 8
  • Karma: +0/-0
    • View Profile
WTS/WTT: T520-2 - Micrometals core, MO, USA
« on: November 15, 2023, 04:03:52 PM »
Hey,

I know I'm new here, but I figured I would offer this in case someone else is building a buck qcw and needs a core capable of handling hundreds of amps. Not selling the whole inductor, just the bare core.

Ordering from micrometals has a minimum of two for this part number, hence my spare. I'm only looking for what I paid for one. $45+shipping.

I am also down for cool trades. Let me know if you have anything you want to swap.

Datasheet: https://datasheets.micrometals.com/T520-2-DataSheet.pdf



Offline flyingperson23

  • High Voltage Technician
  • ***
  • Posts: 170
  • Karma: +5/-2
  • noob :)
    • View Profile
Re: WTS/WTT: T520-2 - Micrometals core, MO, USA
« Reply #1 on: November 18, 2023, 10:38:04 PM »
I'd like to buy it. I PMed you about it.

Offline flyingperson23

  • High Voltage Technician
  • ***
  • Posts: 170
  • Karma: +5/-2
  • noob :)
    • View Profile
Re: WTS/WTT: T520-2 - Micrometals core, MO, USA
« Reply #2 on: November 19, 2023, 01:09:21 AM »
NVM it's too small sorry. If I'm not misreading the datasheet, it looks like with enough turns for a few hundred uH, it saturates at under a hundred amps.

Offline klugesmith

  • High Voltage Senior
  • *****
  • Posts: 741
  • Karma: +22/-0
    • View Profile
Re: WTS/WTT: T520-2 - Micrometals core, MO, USA
« Reply #3 on: November 19, 2023, 05:19:07 PM »
Welcome to the forum!

...If I'm not misreading the datasheet, it looks like with enough turns for a few hundred uH, it saturates at under a hundred amps.
Sounds about right.  In an unsolicited design review:
120 turns would give you 287 uH. 
Then 100 A would put H at 457 Oe (36400 A/m), where permeability is down to 88% of nominal.
B would be 4020 gausses instead of 4570 gausses; L would be down to 256 uH.
There are applications where that might be a reasonable operating point.
The core is big enough for 120 turns of AWG 6 or even AWG 5 wire, presumably stranded with very thin insulation.

I think this material (Mix-02) approaches the maximum energy anyone could store in a core that size. (order of 1 joule)
There's so much distributed air gap, that the nominal relative permeability is only 10.  I hadn't known that catalog parts went that low.
With same winding on higher permeability core material, L would go up and I_sat go down in same proportion, so energy would go down.

[edit] Actually we could get more DC energy in similar size inductor using a laminated steel core with air gap, able to handle more than 15000 gausses before saturation.  Not practical for a switching converter!
« Last Edit: November 19, 2023, 05:33:55 PM by klugesmith »

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2859
  • Karma: +134/-2
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: WTS/WTT: T520-2 - Micrometals core, MO, USA
« Reply #4 on: November 19, 2023, 09:58:27 PM »
Quote
[edit] Actually we could get more DC energy in similar size inductor using a laminated steel core with air gap, able to handle more than 15000 gausses before saturation.  Not practical for a switching converter!
Tape-wound amorphous steel cores are used at 20kHz.  Haven't seen any such cores available surplus.

Quote
If I'm not misreading the datasheet, it looks like with enough turns for a few hundred uH, it saturates at under a hundred amps.
I'm curious about this QCW coil that requires such large buck inductance.  My QCW buck uses a 40uH 400A inductor, switching at 40kHz.
David Knierim

Offline klugesmith

  • High Voltage Senior
  • *****
  • Posts: 741
  • Karma: +22/-0
    • View Profile
Re: WTS/WTT: T520-2 - Micrometals core, MO, USA
« Reply #5 on: November 19, 2023, 10:29:08 PM »
Tape-wound amorphous steel cores are used at 20kHz.  Haven't seen any such cores available surplus.
Good point.   And some vacuum-tube audio output transformers and microphone transformers with punched laminations are characterized up to 20 kHz, where operating power will be low and losses may be high.

I just answered my own question about air gap availability. Mentioned for example in this datasheet:
 https://www.magneticmetals.com/products-materials/tape-wound-cut-cores/
For the application in today's discussion, high flux density and low loss at 20 kHz to 40 kHz are useful, even if gapped design has no use for  high permeability and low magnetizing current.

Offline Anders Mikkelsen

  • Global Moderator
  • High Voltage Experimenter
  • *****
  • Posts: 77
  • Karma: +9/-0
    • View Profile
Re: WTS/WTT: T520-2 - Micrometals core, MO, USA
« Reply #6 on: November 19, 2023, 11:34:16 PM »
Saturation with powder cores does not happen abruptly like with ferrite, but across a very wide range of currents. It's perfectly fine to operate the core with less than 20 % remaining permeability, as long as your design can handle the resulting ripple current.

As mentioned by Dave, it sounds like you are aiming for a lot of inductance for this application and current, and very little drop in inductance. That will require a very large and expensive inductor. As a point of reference, I've done a 16 kW continous buck using a core that cost less than 5 dollars, with over 99 % efficiency. This was using SiC, but at frequencies where IGBTs work well aside from having higher switching losses.

Offline flyingperson23

  • High Voltage Technician
  • ***
  • Posts: 170
  • Karma: +5/-2
  • noob :)
    • View Profile
Re: WTS/WTT: T520-2 - Micrometals core, MO, USA
« Reply #7 on: November 20, 2023, 12:54:58 AM »
I'm making a boost converter, hopefully at least 30kW. Switch is a cm300, for 20khz I'd like at least 400uH 200A. A few of these cores stacked would probably work, but toyota prius hybrids used to have buck/boost converters with beefy inductors, getting a few of those seems like my best bet. Sorry to hijack your thread a little coilerer.

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2859
  • Karma: +134/-2
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: WTS/WTT: T520-2 - Micrometals core, MO, USA
« Reply #8 on: November 20, 2023, 03:36:36 AM »
Quote
Sorry to hijack your thread a little coilerer.
I'm the one who should apologize for hijacking this thread.  You're just answering my question.

Quote
I'm making a boost converter, hopefully at least 30kW. Switch is a cm300, for 20khz I'd like at least 400uH 200A. A few of these cores stacked would probably work, but toyota prius hybrids used to have buck/boost converters with beefy inductors, getting a few of those seems like my best bet.
To continue hijacking ;) I'm still puzzled as to why 400uH is needed.  I'd think 50-100uH would be sufficient.  However, no requirement to answer.
For example (ignoring losses), if 30kW is boosting 240V at 125A to 600V at 50A, duty cycle is 60%, 30us at 20kHz.  100uH would ramp by 72A (= 240V * 30us / 100uH).  To average 125A, inductor current is 125A +-36A (89A to 161A).  50uH would ramp twice as much, 144A total or +-72A, so 53A to 197A.  That still fits within 200A maximum.
David Knierim

Offline flyingperson23

  • High Voltage Technician
  • ***
  • Posts: 170
  • Karma: +5/-2
  • noob :)
    • View Profile
Re: WTS/WTT: T520-2 - Micrometals core, MO, USA
« Reply #9 on: November 20, 2023, 06:07:43 AM »
Ah I see, I was misunderstanding how boost converters worked. I may still be misunderstanding, but It'll be boosting max to 1200v 25A which should be 80% duty cycle so 185A max with 100uH. That's 15% permeability loss with 75 turns, which hopefully is fine. To unhijack your thread coilerer, I would once again like to buy the extra core.

Offline klugesmith

  • High Voltage Senior
  • *****
  • Posts: 741
  • Karma: +22/-0
    • View Profile
Re: WTS/WTT: T520-2 - Micrometals core, MO, USA
« Reply #10 on: November 21, 2023, 04:18:24 AM »
... It'll be boosting max to 1200v 25A which should be 80% duty cycle so 185A max with 100uH.
That suggests your current is 125 A +/- 60 A. Consistent with 100 uH, 240 V, 80% duty cycle, 16 kHz. 

I was going to ask the experts about derating the ampacity of thick wires, to account for skin effect and proximity effect.   Then realized it's not that bad here.   The DC current (125 A) sees full wire area.   The superimposed AC current, which is concentrated away from conductor center, is only 35 amps RMS.

[edit] also, at 30 kW, if we need active cooling for semiconductors we can actively cool the coils and cores.
« Last Edit: November 21, 2023, 04:25:18 AM by klugesmith »

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2859
  • Karma: +134/-2
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: WTS/WTT: T520-2 - Micrometals core, MO, USA
« Reply #11 on: November 21, 2023, 04:54:39 AM »
Quote
Ah I see, I was misunderstanding how boost converters worked. I may still be misunderstanding, but It'll be boosting max to 1200v 25A which should be 80% duty cycle so 185A max with 100uH.
Using 1200V rated IGBT for 1200V output will be problematic.  There is no margin for parasitic inductance.  That is why gate charge etc. for 1200V IGBTs are specified for 600V.  That is typical use voltage, 600V nominal + 600V for spikes and tolerance.  Some list use to 800V.  Beyond that has a high probability of failure.  Given your 200A rather than nominal 600A, perhaps you could bet 1000V output.  Would require good low-inductance interconnect.

If 240V is rectified and unfiltered 240Vac, then calculate at 340Vpeak.  Ripple current will be a little higher than at 240V, but still fine presuming 20kHz.
David Knierim

Offline flyingperson23

  • High Voltage Technician
  • ***
  • Posts: 170
  • Karma: +5/-2
  • noob :)
    • View Profile
Re: WTS/WTT: T520-2 - Micrometals core, MO, USA
« Reply #12 on: November 21, 2023, 06:14:38 AM »
The boost converter is thoroughly actively cooled, and the primary and secondary will be as well. I'm using 1700v bridge igbts, and all the boost converter parts except the switch are rated for at least 1600v. I'll try up to like 1000-1100v out and if the spikes are too much for the cm300, I already have mounting holes for 2 of them in series or more likely just replace it with a single 1700v switch. I'm just using cm300s as that's what I have on hand. Inductor(s) will probably be actively cooled so I'm not worried about wire temperature. Wouldn't the only inductance to worry about be the internal inductance of the igbt and the connection from emitter to bus negative, as all other inductance is effectively in series with the main inductor?

It probably won't be run at more than like 800-900v very often for power draw reasons, I'm just interested to see what happens
« Last Edit: November 21, 2023, 06:26:19 AM by flyingperson23 »

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2859
  • Karma: +134/-2
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: WTS/WTT: T520-2 - Micrometals core, MO, USA
« Reply #13 on: November 23, 2023, 04:31:56 AM »
Quote
Wouldn't the only inductance to worry about be the internal inductance of the igbt and the connection from emitter to bus negative, as all other inductance is effectively in series with the main inductor?
Inductance that matters is the loop through IGBT, diode, and output capacitor.  If using diode internal to CM300, there is relatively small inductance between IGBT collector and diode, perhaps 10-20nH.  Output cap from emitter back to diode anode (unused high-side collector terminal) is where layout will matter most.
David Knierim

Offline coilerer

  • High Voltage Enthusiast
  • *
  • Posts: 8
  • Karma: +0/-0
    • View Profile
Re: WTS/WTT: T520-2 - Micrometals core, MO, USA
« Reply #14 on: November 25, 2023, 01:02:05 PM »
Wow. This thread really took off with some great information! Honestly, most of this is above my head.

@flyingperson23 - The other guy hasn't responded to my reply, so it's yours if you still want it. I'll send you a PM too.

Quote
I'm curious about this QCW coil that requires such large buck inductance.  My QCW buck uses a 40uH 400A inductor, switching at 40kHz.
@davekni - The inductor you see would in the OP is ~100mH. I haven't properly measured it, but I don't think its exact value is super important. I have no formal electronics training (I'm a biologist), so I am basing my design heavily around Loneoceans QCW1.5.

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2859
  • Karma: +134/-2
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: WTS/WTT: T520-2 - Micrometals core, MO, USA
« Reply #15 on: November 25, 2023, 08:04:05 PM »
Quote
@davekni - The inductor you see would in the OP is ~100mH. I haven't properly measured it, but I don't think its exact value is super important. I have no formal electronics training (I'm a biologist), so I am basing my design heavily around Loneoceans QCW1.5.
That makes sense and is probably a reasonable size for your needs.  My question was about flyingperson23's need for several hundered uH and several hundred amps (which this core would not support).  I think that question is reasonably settled now.

Have fun building your QCW coil!
David Knierim

High Voltage Forum

Re: WTS/WTT: T520-2 - Micrometals core, MO, USA
« Reply #15 on: November 25, 2023, 08:04:05 PM »

 


* Recent Topics and Posts

post Re: Problem with SSTC
[Solid State Tesla Coils (SSTC)]
Nunu00
Today at 10:17:36 PM
post Making a HV prove
[Electronic Circuits]
Alberto
Today at 09:01:08 PM
post Re: Problem with SSTC
[Solid State Tesla Coils (SSTC)]
davekni
Today at 01:33:37 AM
post Re: Problem with SSTC
[Solid State Tesla Coils (SSTC)]
Nunu00
Today at 12:17:32 AM
post Re: Restoring a Rogowski coil calibrator
[Capacitor Banks]
davekni
July 11, 2024, 07:38:26 PM
post Re: Restoring a Rogowski coil calibrator
[Capacitor Banks]
klugesmith
July 11, 2024, 06:30:00 PM
post LOD No Double Resonant SSTC?
[Solid State Tesla Coils (SSTC)]
ColinHeath
July 11, 2024, 06:08:30 PM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
July 11, 2024, 12:24:56 PM
post Re: Strange QCW Streamer Behavior
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
July 11, 2024, 06:42:23 AM
post Re: Syntherrupter Lightsaber Sender Programming
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Cameron Prince
July 11, 2024, 05:46:07 AM
post Syntherrupter Lightsaber Sender Programming
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Cameron Prince
July 11, 2024, 05:26:51 AM
post Re: Strange QCW Streamer Behavior
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
July 11, 2024, 02:50:54 AM
post Strange QCW Streamer Behavior
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Coupling
July 11, 2024, 12:59:55 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic Circuits]
petespaco
July 10, 2024, 07:10:34 PM
post Re: Understanding and tracking upper and lower poles of QCW DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 10, 2024, 06:52:42 PM
post Re: Understanding and tracking upper and lower poles of QCW DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Anders Mikkelsen
July 10, 2024, 06:28:19 PM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Alex_1996
July 10, 2024, 01:34:09 PM
post Re: Silicon(e) plasma
[General Chat]
alan sailer
July 10, 2024, 12:09:06 AM
post Re: Problem with SSTC
[Solid State Tesla Coils (SSTC)]
Nunu00
July 09, 2024, 11:52:00 PM
post Understanding and tracking upper and lower poles of QCW DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
July 09, 2024, 07:37:22 PM
post Re: Silicon(e) plasma
[General Chat]
MechatEng2023
July 09, 2024, 07:30:05 PM
post Re: UD2.7C outputs very odd single square wave pulses
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 09, 2024, 03:30:49 AM
post Re: UD2.7C outputs very odd single square wave pulses
[Dual Resonant Solid State Tesla coils (DRSSTC)]
verliebt_in_neukölln17
July 09, 2024, 12:51:02 AM
post Re: UD2.7C outputs very odd single square wave pulses
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 08, 2024, 11:30:44 PM
post Re: Why so cheap?
[General Chat]
alan sailer
July 08, 2024, 10:57:10 PM
post UD2.7C outputs very odd single square wave pulses
[Dual Resonant Solid State Tesla coils (DRSSTC)]
verliebt_in_neukölln17
July 08, 2024, 10:21:01 PM
post Why so cheap?
[General Chat]
MRMILSTAR
July 08, 2024, 09:55:24 PM
post Re: Syntherrupter - A Feature-rich, Polyphonic Interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Cameron Prince
July 08, 2024, 09:18:21 PM
post Re: Syntherrupter - A Feature-rich, Polyphonic Interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Max
July 08, 2024, 05:17:49 PM
post Re: Syntherrupter - A Feature-rich, Polyphonic Interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Cameron Prince
July 08, 2024, 04:49:20 PM
post Re: Tesla coil in FEMM
[Beginners]
Simranjit
July 08, 2024, 04:28:43 AM
post Re: Tesla coil in FEMM
[Beginners]
davekni
July 08, 2024, 04:06:53 AM
post Tesla coil in FEMM
[Beginners]
Simranjit
July 08, 2024, 03:46:49 AM
post Re: Best core material for QCW Buck modulator ?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
July 08, 2024, 02:42:00 AM
post Re: QCWDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
July 08, 2024, 01:37:55 AM
post Re: First DRSSTC Build- Issues with Fibernet project
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Sebigamer
July 08, 2024, 12:53:08 AM
post Re: QCWDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Anders Mikkelsen
July 08, 2024, 12:49:48 AM
post Re: Silicon(e) plasma
[General Chat]
alan sailer
July 07, 2024, 11:15:35 PM
post Silicon(e) plasma
[General Chat]
MechatEng2023
July 07, 2024, 11:04:43 PM
post Re: QCWDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
July 07, 2024, 09:39:07 PM
post Re: First DRSSTC Build- Issues with Fibernet project
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 07, 2024, 05:32:56 PM
post Re: QCWDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Anders Mikkelsen
July 07, 2024, 02:52:19 PM
post Re: No change in Phase Lead
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Anders Mikkelsen
July 07, 2024, 02:50:04 PM
post Re: Best core material for QCW Buck modulator ?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Anders Mikkelsen
July 07, 2024, 02:20:11 PM
post Teardown of a APC SmartUPS VT 40 kVA
[Electronic Circuits]
Mads Barnkob
July 07, 2024, 10:02:22 AM
post First DRSSTC Build- Issues with Fibernet project
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Sebigamer
July 07, 2024, 09:23:58 AM
post Re: QCWDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
July 07, 2024, 12:44:53 AM
post Re: FEMM tesla coil simulation
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
July 07, 2024, 12:08:50 AM
post Re: FEMM tesla coil simulation
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
July 06, 2024, 10:35:49 PM
post FEMM tesla coil simulation
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
July 06, 2024, 09:42:43 PM
post Re: No change in Phase Lead
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 06, 2024, 06:06:23 PM
post Re: No change in Phase Lead
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
July 06, 2024, 10:21:16 AM
post Re: No change in Phase Lead
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
July 06, 2024, 10:15:42 AM
post Re: QCWDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
July 06, 2024, 04:53:56 AM
post Re: No change in Phase Lead
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
July 06, 2024, 04:42:16 AM
post Re: QCWDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
July 06, 2024, 04:09:50 AM
post Re: Best core material for QCW Buck modulator ?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 06, 2024, 03:07:11 AM
post Re: No change in Phase Lead
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 06, 2024, 03:05:18 AM
post Re: QCWDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
July 06, 2024, 02:37:16 AM
post Re: QCWDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
July 06, 2024, 02:20:14 AM
post QCWDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
July 06, 2024, 01:55:14 AM
post Re: No change in Phase Lead
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
July 05, 2024, 11:50:37 PM
post Best core material for QCW Buck modulator ?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
July 05, 2024, 10:07:04 PM
post 230v Tesla coil and krypton gas
[Spark Gap Tesla Coils (SGTC)]
gravitysrainbow
July 05, 2024, 07:13:25 PM
post Re: No change in Phase Lead
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
July 05, 2024, 06:17:13 PM
post Re: Phase lead inductors
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
July 04, 2024, 11:40:45 PM
post Re: Sling Psychrometer
[Laboratories, Equipment and Tools]
Twospoons
July 04, 2024, 11:02:32 PM
post Phase lead inductors
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 04, 2024, 06:28:08 PM
post Re: Sling Psychrometer
[Laboratories, Equipment and Tools]
klugesmith
July 04, 2024, 12:31:40 AM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Alex_1996
July 04, 2024, 12:07:21 AM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Alex_1996
July 04, 2024, 12:06:17 AM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
July 03, 2024, 10:51:23 PM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
July 03, 2024, 09:44:14 PM
post Re: Coax cable for DRSSTC interrupter?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
July 03, 2024, 08:48:13 PM
post Re: Coax cable for DRSSTC interrupter?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
July 03, 2024, 08:24:50 PM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Alex_1996
July 03, 2024, 08:12:55 PM
post Re: Coax cable for DRSSTC interrupter?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
July 03, 2024, 07:29:53 PM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
July 03, 2024, 07:21:38 PM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 03, 2024, 05:05:39 PM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Alex_1996
July 03, 2024, 04:29:53 PM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 03, 2024, 04:09:11 PM
post FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Alex_1996
July 03, 2024, 02:47:18 PM
post Re: Eliminating discharges from a SSTC
[Solid State Tesla Coils (SSTC)]
Alex_1996
July 03, 2024, 01:35:24 PM
post Re: Coax cable for DRSSTC interrupter?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 03, 2024, 02:19:03 AM
post Re: Coax cable for DRSSTC interrupter?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
verliebt_in_neukölln17
July 03, 2024, 01:19:50 AM
post Coax cable for DRSSTC interrupter?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
July 02, 2024, 11:29:18 PM
post Re: Is this a good pulse experiment capacitor?
[Capacitor Banks]
Mads Barnkob
July 02, 2024, 09:59:07 PM
post Re: LabCoatz Staccato QCW No straight sparks
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
July 02, 2024, 09:55:53 PM
post Re: Capacitor wiring for single phase 240 to split phase (180 degree) 240v
[Capacitor Banks]
klugesmith
July 02, 2024, 09:44:55 PM
post Re: LabCoatz Staccato QCW No straight sparks
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
July 02, 2024, 07:51:37 PM
post Re: LabCoatz Staccato QCW No straight sparks
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
July 02, 2024, 06:14:07 PM
post Is this a good pulse experiment capacitor?
[Capacitor Banks]
FPS
July 02, 2024, 06:02:38 PM
post Re: LabCoatz Staccato QCW No straight sparks
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
July 02, 2024, 11:37:46 AM
post Re: Building my first DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
July 02, 2024, 05:22:10 AM
post Re: Coulometric hourmeters
[Laboratories, Equipment and Tools]
davekni
July 02, 2024, 05:16:30 AM
post Re: Building my first DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
drobotk
July 01, 2024, 11:50:12 PM
post Re: Restoring a Rogowski coil calibrator
[Capacitor Banks]
klugesmith
July 01, 2024, 08:48:53 PM
post Uses for Weston's Little Bee probe
[Laboratories, Equipment and Tools]
klugesmith
July 01, 2024, 08:40:59 AM
post Re: Coulometric hourmeters
[Laboratories, Equipment and Tools]
klugesmith
July 01, 2024, 08:09:42 AM
post Re: Coulometric hourmeters
[Laboratories, Equipment and Tools]
davekni
June 30, 2024, 06:49:45 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal