Author Topic: First drsstc issues  (Read 4899 times)

Offline Hari33

  • High Voltage Enthusiast
  • *
  • Posts: 19
  • Karma: +0/-0
    • View Profile
First drsstc issues
« on: September 19, 2023, 07:39:42 PM »
Hello,I am an absolute beginner to drsstc. thanks to this forum I carried out the first test of my not-so-well made drsstc in my university laboratory.
The output is very bad, I only get small sparks when the secondary base wire gets close to the top load.
I gave feedback pulses from a signal generator because feedback doesn't work well.

These are the specifications of the coil
-half bridge of 60n60fd1 igbt
- 2000 secondary turns (36 AWG wire)
- 8 turns primary (14 awg) - cylindrical primary
- 80us on time of interrupter
-0.1uf tank capacitor 2.4kvdc
-javatc says the resonance frequency is 260 khz .
(I am getting those tiny sparks only when i am giving 260khz sine wave from signal generator to the feedback).

Gdt waveforms are good.
The gate waveforms are changing when the voltage input is increased.

I tried scoping the feedback ct when running the coil with feedback pulses from signal generator, those waveforms are a mess.the ratio of ct is 1:500.

primary coil draws almost 12 amps with only 50 volts AC

Could you suggest some troubleshooting tips?

Thank you.
« Last Edit: September 30, 2023, 10:03:17 PM by Hari33 »

Offline Mads Barnkob

  • Administrator
  • Executive Board Member
  • *****
  • Posts: 2299
  • Karma: +73/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: First drsstc issues
« Reply #1 on: September 19, 2023, 08:18:38 PM »
Hi Hari and welcome to HVF

When you run with a signal generator, you do not get the dynamic feedback of the changing resonant frequency, due to spark loading or other disturbances to the resonant system.

You risk blowing up your IGBTs from hard switching too high currents this way.

Did you check that phasing is correct of your GDT connections? Did you try to switch polarity of driver signal (what driver are you using?) with the jumpers or switching polarity on the primary coil?

The small sparks does resemble wrong phasing, as all spark you see is the small overlap in the dead-time.
https://kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline Hari33

  • High Voltage Enthusiast
  • *
  • Posts: 19
  • Karma: +0/-0
    • View Profile
Re: First drsstc issues
« Reply #2 on: September 19, 2023, 09:18:47 PM »
 Thank you so much for the reply.🙏

I am using Steve Wards 1.3b driver.

I tried reversing the CT secondary wires, but there is no difference.could you please tell how to check if phasing is right?.

I didnt try reversing the polarity of primary? Will update the result after doing it today.

Also could you please clear these beginner doubts?

-How does intially the feedback CT's give feedback to the driver if there is no current flowing in primary during startup in a drsstc?.

-what would be causing the change in gate waveforms when the voltage to the primary is increased?

-These tiny sparks that i get, i am getting this only at around 260khz from the signal generator, this means that 260khz is the resonant freqency of the secondary?( java tc says 260khz)

-Isnt this current draw abnormal for a small drsstc at this voltage?

Thank you
« Last Edit: September 19, 2023, 09:57:47 PM by Hari33 »

Offline Hari33

  • High Voltage Enthusiast
  • *
  • Posts: 19
  • Karma: +0/-0
    • View Profile
Re: First drsstc issues
« Reply #3 on: September 30, 2023, 10:01:31 PM »
Hi, I solved a lot of the issues with my first drsstc, now i am stuck with another one.
I was finally able to get the primary self oscillating by fixing some noise in the driver, but now the issue is the primary resonating at a different frequency(125khz) than what is specified by Javatc(250khz).
I tried fixing the issue by tuning it by adding more capacitors in series to mmc (mmc = 6×0.24uf mkp capacitors used in induction cookers) to increase the primary frequency to match the secondary frequency which is 260khz according to javatc.When the primary and secondary frequencies are matched, the primary feedback amplitude has reduced a lot ( primary current has decreased) also very small arcs, now the half bridge is drawing only 1.5 amp whereas it was drawing 5 amps when primary was resonating at 125Khz.

This is the problem i stuck with now.
Could this be because of the added esr in mmc?

In the pic i am attaching, blue is secondary current waveform and yellow is primary feedback.
« Last Edit: September 30, 2023, 10:04:34 PM by Hari33 »

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2820
  • Karma: +134/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: First drsstc issues
« Reply #4 on: October 01, 2023, 07:14:40 PM »
Quote
In the pic i am attaching, blue is secondary current waveform and yellow is primary feedback.
200V on primary feedback indicates input diodes of UD1.3b are open-circuit.  After replacing those diodes, I'd start again back with JavaTC calculated MMC value.
David Knierim

Offline Hari33

  • High Voltage Enthusiast
  • *
  • Posts: 19
  • Karma: +0/-0
    • View Profile
Re: First drsstc issues
« Reply #5 on: October 02, 2023, 03:59:17 PM »
Quote
In the pic i am attaching, blue is secondary current waveform and yellow is primary feedback.
200V on primary feedback indicates input diodes of UD1.3b are open-circuit.  After replacing those diodes, I'd start again back with JavaTC calculated MMC value.

I replaced the diodes and today measured the primary feedback across a 3 ohm burden resistance, i am using a 1:500 ct.Now its measuring almost 0.9 volts peak across the resistor, so its 150 amps through the primary. I kept a big cylindrical topload and reduced the secondary frequency to 210 khz.I measured the primary resonance manually with a mmc of 60nf, and its around 205 khz.
At 300vdc on the bus,even though the sparks are bigger when i am bringing the earth wire near the top load, they are not breaking out on its own.



Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2820
  • Karma: +134/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: First drsstc issues
« Reply #6 on: October 03, 2023, 02:53:26 AM »
Quote
I replaced the diodes and today measured the primary feedback across a 3 ohm burden resistance, i am using a 1:500 ct.Now its measuring almost 0.9 volts peak across the resistor, so its 150 amps through the primary.
Do you have a separate measurement CT for the 3 ohm burden resistance?  Or are you adding 3 ohms in parallel with UD1.3b feedback CT input?  If the latter, that is preventing proper UD1.3b operation.
David Knierim

Offline Hari33

  • High Voltage Enthusiast
  • *
  • Posts: 19
  • Karma: +0/-0
    • View Profile
Re: First drsstc issues
« Reply #7 on: October 03, 2023, 05:13:00 AM »
Quote
Do you have a separate measurement CT for the 3 ohm burden resistance?  Or are you adding 3 ohms in parallel with UD1.3b feedback CT input?  If the latter, that is preventing proper UD1.3b operation.

Yes, i have a separate ct for feedback measurement.

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2820
  • Karma: +134/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: First drsstc issues
« Reply #8 on: October 03, 2023, 05:14:06 AM »
Is there now a +-5V square wave on UD1.3b feedback input with replaced diodes?
David Knierim

Offline Hari33

  • High Voltage Enthusiast
  • *
  • Posts: 19
  • Karma: +0/-0
    • View Profile
Re: First drsstc issues
« Reply #9 on: October 03, 2023, 09:40:15 AM »
Is there now a +-5V square wave on UD1.3b feedback input with replaced diodes?
Yes there is 👍

Offline Hari33

  • High Voltage Enthusiast
  • *
  • Posts: 19
  • Karma: +0/-0
    • View Profile
Re: First drsstc issues
« Reply #10 on: October 03, 2023, 06:40:29 PM »
I got my first light today!!.
I got it when the phase difference between primary and secondary was around 180 degrees.
Is this how its supposed to be?
Yellow is primary current and blue is secondary.
« Last Edit: October 03, 2023, 08:09:59 PM by Hari33 »

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2820
  • Karma: +134/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: First drsstc issues
« Reply #11 on: October 05, 2023, 05:13:03 AM »
Quote
I got it when the phase difference between primary and secondary was around 180 degrees.
Is this how its supposed to be?
Presuming CTs are all the correct way around so current is truly 180 degrees, that indicates operation at upper pole frequency.  Likely primary is tuned above secondary.  I don't see any of the typical cyclic power transfer from primary to secondary and back.  If tuning is close (similar primary and secondary frequencies), energy cycles back and forth between primary and secondary.  Tuning may be quite a ways off.
David Knierim

Offline Hari33

  • High Voltage Enthusiast
  • *
  • Posts: 19
  • Karma: +0/-0
    • View Profile
Re: First drsstc issues
« Reply #12 on: November 11, 2023, 05:26:40 PM »
Hi, it took a while for me to restart the work of the drsstc.
Finally I got the 1.3b driver printed and the small drsstc is working fine, most of its issues disappeared once i started using pcb instead of the driver that i made on breadboards.
it's able to give out 30cm arcs easily.

I started working on a bigger coil this week, everything is going good except the feedback, its working fine giving out 50cm arcs with a signal generator but it's not oscillating on it's own, the ocd is also working good.
This is the first time I am making a full bridge with igbt half bridge modules. I am using 2 old bsm100gb60dlc which I salvaged from an old inverter.

I checked the output of the gdt and its showing the initial startup pulses given by the interrupter.
Some how that is not making the igbts work.
(No output from bridge at the time of startup pulses)

Gate voltage is 18volts, interrupter-140 bps( 80us on time).
Gate resistor - 5 ohms
Ct - 1:1000 (3 ferrite cores cascaded,10 turns each)

Any tips for debugging would of great help.
Thank you
« Last Edit: November 11, 2023, 06:56:34 PM by Hari33 »

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2820
  • Karma: +134/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: First drsstc issues
« Reply #13 on: November 12, 2023, 01:44:31 AM »
Second paragraph of this post may help even though it was in an SSTC thread:
https://highvoltageforum.net/index.php?topic=840.msg5667#msg5667
There are several other discussions about startup issues on the forum.  Adding a power resistor across H-bridge outputs is the key take-away from above post, as recommended by Mads in his posts and web pages.
David Knierim

Offline Hari33

  • High Voltage Enthusiast
  • *
  • Posts: 19
  • Karma: +0/-0
    • View Profile
Re: First drsstc issues
« Reply #14 on: November 12, 2023, 08:23:32 AM »
Thanks for sharing this, will try this and see how it goes.

Offline Hari33

  • High Voltage Enthusiast
  • *
  • Posts: 19
  • Karma: +0/-0
    • View Profile
Re: First drsstc issues
« Reply #15 on: November 17, 2023, 07:16:05 PM »
Hi, i tried keeping a 100k 1W resistor across the bridge output,but it didnt work.
I also tried keeping a 100k resitor across the 1 and 2 pins of the 74hc14 to make the 1.3 driver self starting,this is working but the coil is having a lot of breaks in between.

There is no ct output when the interrupter is giving the startup pulses.

The coil is working well when its run with a signal generator.

And can someone please explain why making the drsstc using sine waves from a signal generator is a bad idea.
The feedback from ct is also a sine wave righ?, and wont the flip flop of 1.3b driver ensure soft switching the igbts?
Isn't it just the secondary frequency that gets affected by breakout and other factors, does the primary get affected too?

« Last Edit: November 17, 2023, 08:11:06 PM by Hari33 »

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2820
  • Karma: +134/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: First drsstc issues
« Reply #16 on: November 17, 2023, 07:23:36 PM »
Quote
There is no ct output when the interrupter is giving the startup pulses.
Something is mis-wired or broken in your UD1.3.  I'd scope through UD1.3 from interrupter to driver outputs (GDT primary) to see where signal is getting lost.
David Knierim

Offline Egg

  • High Voltage Enthusiast
  • *
  • Posts: 36
  • Karma: +1/-0
    • View Profile
Re: First drsstc issues
« Reply #17 on: November 17, 2023, 07:28:02 PM »
And can someone please explain why making the drsstc using sine waves from a signal generator is a bad idea.
The feedback from ct is also a sine wave righ?, and wont the flip flop of 1.3b driver ensure soft switching the igbts?
Isn't it just the secondary frequency that gets affected by breakout and other factors, does the primary get affected too?


If you run the circuit through signal generator input than you lose the primary feedback which is the main benefit of the drsstc, where you have super rapid current growth. With no feedback you will not achieve that since being even a little off on the freq causes some impedance on primary circuit.

Offline Hari33

  • High Voltage Enthusiast
  • *
  • Posts: 19
  • Karma: +0/-0
    • View Profile
Re: First drsstc issues
« Reply #18 on: November 17, 2023, 08:04:56 PM »
Quote
There is no ct output when the interrupter is giving the startup pulses.
Something is mis-wired or broken in your UD1.3.  I'd scope through UD1.3 from interrupter to driver outputs (GDT primary) to see where signal is getting lost.

There is gdt output during the startup pulses, but its just that the bridge is not working at those pulses.
I am assuming that the bridge is not working because there is no feedback ct output at the time of those start up pulses
« Last Edit: November 17, 2023, 08:12:41 PM by Hari33 »

Offline Hari33

  • High Voltage Enthusiast
  • *
  • Posts: 19
  • Karma: +0/-0
    • View Profile
Re: First drsstc issues
« Reply #19 on: November 17, 2023, 08:09:01 PM »
And can someone please explain why making the drsstc using sine waves from a signal generator is a bad idea.
The feedback from ct is also a sine wave righ?, and wont the flip flop of 1.3b driver ensure soft switching the igbts?
Isn't it just the secondary frequency that gets affected by breakout and other factors, does the primary get affected too?


If you run the circuit through signal generator input than you lose the primary feedback which is the main benefit of the drsstc, where you have super rapid current growth. With no feedback you will not achieve that since being even a little off on the freq causes some impedance on primary circuit.

Thank you🙌
But what if the the system is tuned and signal generator is used to produce sine waves having frequency of the primary?

High Voltage Forum

Re: First drsstc issues
« Reply #19 on: November 17, 2023, 08:09:01 PM »

 


* Recent Topics and Posts

post Re: Turning SSTC into DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
Today at 02:14:17 AM
post Re: Turning SSTC into DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
June 12, 2024, 11:04:57 PM
post Turning SSTC into DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
June 12, 2024, 10:23:08 PM
post Re: UD2.7C constantly in OCP despite having signal
[Dual Resonant Solid State Tesla coils (DRSSTC)]
verliebt_in_neukölln17
June 12, 2024, 08:41:06 PM
post Re: UD2.7C constantly in OCP despite having signal
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
June 12, 2024, 07:53:31 PM
post Re: Van de Graaf Voltage measurement with voltage sensor and voltage divider
[Static Electricity]
haversin
June 12, 2024, 06:57:13 PM
post UD2.7C constantly in OCP despite having signal
[Dual Resonant Solid State Tesla coils (DRSSTC)]
verliebt_in_neukölln17
June 12, 2024, 06:54:49 PM
post Re: Van de Graaf Voltage measurement with voltage sensor and voltage divider
[Static Electricity]
Mads Barnkob
June 12, 2024, 03:47:28 PM
post Van de Graaf Voltage measurement with voltage sensor and voltage divider
[Static Electricity]
vK
June 12, 2024, 03:42:18 AM
post Re: Bigger sparks?...
[Vacuum Tube Tesla Coils (VTTC)]
davekni
June 12, 2024, 03:32:22 AM
post Re: Bigger sparks?...
[Vacuum Tube Tesla Coils (VTTC)]
Teslaventje
June 11, 2024, 11:05:49 PM
post Re: Bigger sparks?...
[Vacuum Tube Tesla Coils (VTTC)]
MRMILSTAR
June 11, 2024, 05:36:46 AM
post Re: Sling Psychrometer
[Laboratories, Equipment and Tools]
Twospoons
June 11, 2024, 12:29:31 AM
post Bigger sparks?...
[Vacuum Tube Tesla Coils (VTTC)]
Teslaventje
June 10, 2024, 11:05:55 PM
post Re: Syntherrupter - A Feature-rich, Polyphonic Interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Max
June 10, 2024, 10:57:51 PM
post Re: Benjamin's DRSSTC3
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
June 10, 2024, 08:08:04 PM
post Re: Plasma Torid - Class E Self Resonant Dual/Stereo - Plasma Torid Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hi-Deff
June 10, 2024, 06:04:09 PM
post Sling Psychrometer
[Laboratories, Equipment and Tools]
klugesmith
June 10, 2024, 04:43:59 PM
post Re: Benjamin's DRSSTC3
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
June 10, 2024, 03:35:28 PM
post Re: Benjamin's DRSSTC3
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Jj
June 10, 2024, 01:36:41 PM
post Re: Is a 60UF 800VDC Dawncap good for an induction heater?
[General Chat]
Anders Mikkelsen
June 09, 2024, 05:44:29 PM
post Is a 60UF 800VDC Dawncap good for an induction heater?
[General Chat]
yourboi
June 09, 2024, 03:31:30 PM
post Re: Steve Ward's DRSSTC Interrupter stops working when adjusting pulse width
[Electronic Circuits]
NyaaX_X
June 09, 2024, 01:34:49 PM
post Steve Ward's DRSSTC Interrupter stops working when adjusting pulse width
[Electronic Circuits]
verliebt_in_neukölln17
June 09, 2024, 01:56:51 AM
post Re: Return of Electronics Flea Market in "Silicon Valley"
[Sell / Buy / Trade]
klugesmith
June 08, 2024, 06:06:25 AM
post Re: Coulometric hourmeters
[Laboratories, Equipment and Tools]
klugesmith
June 08, 2024, 05:38:14 AM
post Interrupter for SSTC
[Beginners]
Simranjit
June 08, 2024, 12:47:47 AM
post Re: Adding capacitor to primary in SSTC
[Solid State Tesla Coils (SSTC)]
Michelle_
June 07, 2024, 03:59:57 PM
post Re: Adding capacitor to primary in SSTC
[Solid State Tesla Coils (SSTC)]
davekni
June 07, 2024, 06:42:26 AM
post Re: Space-X Starship test this week
[Science, Research and News In Other Fields Than Electronics]
MRMILSTAR
June 07, 2024, 05:08:00 AM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
davekni
June 07, 2024, 03:16:31 AM
post Re: Space-X Starship test this week
[Science, Research and News In Other Fields Than Electronics]
klugesmith
June 06, 2024, 11:37:20 PM
post Adding capacitor to primary in SSTC
[Solid State Tesla Coils (SSTC)]
Simranjit
June 06, 2024, 11:20:23 PM
post Re: Plasma Torid - Class E Self Resonant Dual/Stereo - Plasma Torid Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
June 06, 2024, 10:54:48 PM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
ZakW
June 06, 2024, 05:17:02 AM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
Simranjit
June 06, 2024, 04:50:00 AM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
davekni
June 06, 2024, 04:00:52 AM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
ZakW
June 06, 2024, 01:43:41 AM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
Simranjit
June 05, 2024, 11:11:17 PM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
Michelle_
June 05, 2024, 10:18:57 PM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
Simranjit
June 05, 2024, 10:13:03 PM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
ZakW
June 05, 2024, 09:29:18 PM
post Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
Simranjit
June 05, 2024, 08:46:53 PM
post Re: Want to build HV HF oscilloscope probe.
[Electronic Circuits]
Twospoons
June 05, 2024, 07:04:45 AM
post Re: Want to build HV HF oscilloscope probe.
[Electronic Circuits]
Domo
June 05, 2024, 04:58:35 AM
post Re: Pearson current monitor model 1330 teardown (100kA)
[Laboratories, Equipment and Tools]
klugesmith
June 05, 2024, 01:42:04 AM
post Re: Coulometric hourmeters
[Laboratories, Equipment and Tools]
klugesmith
June 04, 2024, 10:31:58 PM
post Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
pete_dl
June 04, 2024, 08:08:28 PM
post Re: Want to build HV HF oscilloscope probe.
[Electronic Circuits]
Twospoons
June 03, 2024, 11:13:26 PM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
June 03, 2024, 10:35:57 PM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hi-Deff
June 03, 2024, 05:51:05 PM
post Re: Want to build HV HF oscilloscope probe.
[Electronic Circuits]
Domo
June 03, 2024, 07:41:41 AM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
June 03, 2024, 05:28:44 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
June 03, 2024, 05:02:19 AM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
June 03, 2024, 03:47:33 AM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
June 03, 2024, 02:23:58 AM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hi-Deff
June 03, 2024, 01:25:24 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
June 03, 2024, 01:08:47 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
June 02, 2024, 10:29:02 PM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Michelle_
June 02, 2024, 10:02:45 PM
post Re: Racing sparks
[Spark Gap Tesla Coils (SGTC)]
davekni
June 02, 2024, 08:25:37 PM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Michelle_
June 02, 2024, 04:51:58 PM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Michelle_
June 02, 2024, 04:44:30 PM
post Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
MRMILSTAR
June 02, 2024, 03:25:11 PM
post APC Smart-UPS 1500VA Teardown
[Electronic Circuits]
Mads Barnkob
June 02, 2024, 01:36:11 PM
post Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
pete_dl
June 02, 2024, 11:43:40 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
June 02, 2024, 08:49:11 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
June 02, 2024, 08:36:07 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
June 02, 2024, 12:41:50 AM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Benjamin Lockhart
June 01, 2024, 08:24:35 PM
post Pearson current monitor model 1330 teardown (100kA)
[Laboratories, Equipment and Tools]
Mads Barnkob
June 01, 2024, 08:22:28 PM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Michelle_
June 01, 2024, 03:56:53 AM
post Re: Racing sparks
[Spark Gap Tesla Coils (SGTC)]
Terry
June 01, 2024, 12:03:50 AM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hi-Deff
May 31, 2024, 11:46:20 PM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Michelle_
May 31, 2024, 06:13:59 PM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
May 31, 2024, 01:55:22 AM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
May 30, 2024, 11:57:49 PM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
May 30, 2024, 11:50:06 PM
post First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hi-Deff
May 30, 2024, 11:23:35 PM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
davekni
May 30, 2024, 10:43:06 PM
post Re: Benjamin's DRSSTC3
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
May 30, 2024, 10:24:35 PM
post Re: SSTC tripping circuit breaker
[Solid State Tesla Coils (SSTC)]
NyaaX_X
May 30, 2024, 06:10:04 PM
post Re: SSTC tripping circuit breaker
[Solid State Tesla Coils (SSTC)]
Simranjit
May 30, 2024, 04:56:11 PM
post Re: SSTC tripping circuit breaker
[Solid State Tesla Coils (SSTC)]
Michelle_
May 30, 2024, 04:48:05 PM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Michelle_
May 30, 2024, 04:37:22 PM
post Re: SSTC tripping circuit breaker
[Solid State Tesla Coils (SSTC)]
klugesmith
May 30, 2024, 04:16:31 PM
post Re: SSTC tripping circuit breaker
[Solid State Tesla Coils (SSTC)]
NyaaX_X
May 30, 2024, 03:34:10 PM
post Re: SSTC tripping circuit breaker
[Solid State Tesla Coils (SSTC)]
Simranjit
May 30, 2024, 02:53:50 PM
post Re: SSTC tripping circuit breaker
[Solid State Tesla Coils (SSTC)]
NyaaX_X
May 30, 2024, 12:44:47 PM
post SSTC tripping circuit breaker
[Solid State Tesla Coils (SSTC)]
Simranjit
May 30, 2024, 07:52:56 AM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
NyaaX_X
May 30, 2024, 07:07:53 AM
post Re: Benjamin's DRSSTC3
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
May 30, 2024, 07:04:40 AM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Michelle_
May 30, 2024, 05:16:50 AM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Michelle_
May 30, 2024, 05:08:17 AM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
davekni
May 30, 2024, 04:29:30 AM
post Re: Benjamin's DRSSTC3
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
May 30, 2024, 03:52:36 AM
post Re: Racing sparks
[Spark Gap Tesla Coils (SGTC)]
davekni
May 30, 2024, 03:47:12 AM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Benjamin Lockhart
May 30, 2024, 03:41:34 AM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Michelle_
May 30, 2024, 03:27:28 AM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Michelle_
May 29, 2024, 03:55:16 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal