Author Topic: Gap distance between main bus bar  (Read 2154 times)

Offline SAMGO

  • High Voltage Enthusiast
  • *
  • Posts: 21
  • Karma: +2/-0
    • View Profile
Gap distance between main bus bar
« on: October 26, 2021, 01:13:09 PM »
Hi to everyone, hope you are all doing well,

I'm now in the process of building a new DRSSTC and I have a question about my inverter design.
My inverter is based on two GD600HFY120C2S, see datasheet in attachement, running at around 560VDC from 3 phase supply. For the bus capacitance I'm using a 2s2p configuration of 4700uF 400VDC caps. The input of the 3 phase 80A rectifier is protected by 10A type C circuit breaker for added safety.

The gap between + and - it's now 2mm, this is okay for 560VDC but I was wondering if this could be a problem because of transients voltages.

If a transient comes it will be limited at the voltage necessary to fill the gap between + and - . In this way I can protect my IGBTs, maybe at the cost of loosing my 3 phase rectifier but it's cheaper and easy to change. The problem is that in this case the arc will also make the bus caps discharge and I have the feeling that is is not good and could kill the IGBTs in some strange way   :(

I'm now trying to decide between leaving it this way or putting a insulator layer / milling away some copper to enlarge the space between rails.

What do you think will be the better solution ?

Here is my Inverter so far, it's still missing the heatsink:




I also  made a small and simple circuit to safely discharge the main caps. The basic idea is to have an emergercy stop switch that will both open the 3 phase supply and put a power discharge resistor between + and - , this will also work if the 230V driver circuit it's un-plugged.

You can check it here:

Offline TMaxElectronics

  • High Voltage Engineer
  • ****
  • Posts: 297
  • Karma: +23/-0
    • View Profile
    • My random (and very empty) electronics blog
Re: Gap distance between main bus bar
« Reply #1 on: October 26, 2021, 06:38:24 PM »
With the width of your bus bars you could probably increase the spacing quite easily by drilling one of the mounting holes off-center. That would allow you to move the bus bar on the outer terminal further out, increasing the spacing considerably.

You will also need a pre-charge resistor for the dc bus. The inrush current of charging up such a large capacitance directly from the mains is massive, and will very likely cause problems.

I also think that a 10A breaker for such a high power coil is a little small. I managed to trip the breaker on my 3 phase 16A outlet in a matter of seconds with my skm400 coil and I suspect your inverter might do the same :)
And a type C breaker won't help do mucht to protect the semiconductors. if anything goes wrong the bus capacitance is likely enough to kill them by it self. I'd recommend just not installing a breaker on your coil directly, since all it would protect is the cabelling and that is already protected by the breaker in the distribution box.

Offline SAMGO

  • High Voltage Enthusiast
  • *
  • Posts: 21
  • Karma: +2/-0
    • View Profile
Re: Gap distance between main bus bar
« Reply #2 on: October 26, 2021, 08:29:08 PM »
With the width of your bus bars you could probably increase the spacing quite easily by drilling one of the mounting holes off-center. That would allow you to move the bus bar on the outer terminal further out, increasing the spacing considerably.

You will also need a pre-charge resistor for the dc bus. The inrush current of charging up such a large capacitance directly from the mains is massive, and will very likely cause problems.

I also think that a 10A breaker for such a high power coil is a little small. I managed to trip the breaker on my 3 phase 16A outlet in a matter of seconds with my skm400 coil and I suspect your inverter might do the same :)
And a type C breaker won't help do mucht to protect the semiconductors. if anything goes wrong the bus capacitance is likely enough to kill them by it self. I'd recommend just not installing a breaker on your coil directly, since all it would protect is the cabelling and that is already protected by the breaker in the distribution box.

Thanks TMax that's actually a good idea, I'll take note and see what to do when my fat heatsink arrives. Actually the holes are already off-center but I forgot that the widht of the busbars was changed last minute bruh :(

For the circuit breaker it's true that it doesn't add a lot of protection. I think I will go with the 10A one for the test phase and that evaluate to skip it when everything work as it should if necessary.
 
I agree with you about the pre-charge resistor, there is no way it will work if I attach it to 400VAC directly. For now I will be using a variac to be able to run it at a lower bus voltage. When everything works I will put 3 pre-charge resistors that get shorted after some seconds by a relais and regulate power via on-time.

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2745
  • Karma: +130/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: Gap distance between main bus bar
« Reply #3 on: October 26, 2021, 11:08:03 PM »
Quote
The gap between + and - it's now 2mm, this is okay for 560VDC but I was wondering if this could be a problem because of transients voltages.
If 2mm is air gap only, shouldn't be much risk.  A 2mm surface path (creepage distance) would be concerning.  Even for air, 3 or 4 or 5mm wouldn't hurt for comfort.  I'd think the risk is less from transients and more from any fine metal whiskers or other conductive debris falling or blowing across the gap and starting an arc.
David Knierim

Offline klugesmith

  • High Voltage Senior
  • *****
  • Posts: 688
  • Karma: +22/-0
    • View Profile
Re: Gap distance between main bus bar
« Reply #4 on: October 27, 2021, 03:14:57 AM »
>> I'd think the risk is less from transients and more from any fine metal whiskers or other conductive debris falling or blowing across the gap and starting an arc.

At work we had a problem with low-voltage busbar parts made of copper and plated with pure tin.   Tin whisker growth is a real thing, even today.

Offline Duane B

  • High Voltage Experimenter
  • **
  • Posts: 55
  • Karma: +3/-0
    • View Profile
    • Roaring 20s Superhets
Re: Gap distance between main bus bar
« Reply #5 on: October 27, 2021, 08:20:13 PM »
A 2mm gap might be troublesome with thermal expansion, dirt and debris over time. You might be better off increasing the distance of the gap and installing some type of MOV across the bus.
Duane Bylund

Offline klugesmith

  • High Voltage Senior
  • *****
  • Posts: 688
  • Karma: +22/-0
    • View Profile
Re: Gap distance between main bus bar
« Reply #6 on: October 28, 2021, 07:59:25 PM »
You can look up clearance and creepage rules for your working voltage.
https://www.protoexpress.com/blog/importance-pcb-line-spacing-creepage-clearance/#Calculating_PCB_creepage_and_clearance

I would never depend on the 2 mm spacing as an intentional spark gap to protect components from an overvoltage transient.  So why not insert an insulating sheet to keep debris away from gap?

Offline SAMGO

  • High Voltage Enthusiast
  • *
  • Posts: 21
  • Karma: +2/-0
    • View Profile
Re: Gap distance between main bus bar
« Reply #7 on: November 06, 2021, 11:47:09 PM »
Quote
The gap between + and - it's now 2mm, this is okay for 560VDC but I was wondering if this could be a problem because of transients voltages.
If 2mm is air gap only, shouldn't be much risk.  A 2mm surface path (creepage distance) would be concerning.  Even for air, 3 or 4 or 5mm wouldn't hurt for comfort.  I'd think the risk is less from transients and more from any fine metal whiskers or other conductive debris falling or blowing across the gap and starting an arc.

A 2mm gap might be troublesome with thermal expansion, dirt and debris over time. You might be better off increasing the distance of the gap and installing some type of MOV across the bus.

You can look up clearance and creepage rules for your working voltage.
https://www.protoexpress.com/blog/importance-pcb-line-spacing-creepage-clearance/#Calculating_PCB_creepage_and_clearance

I would never depend on the 2 mm spacing as an intentional spark gap to protect components from an overvoltage transient.  So why not insert an insulating sheet to keep debris away from gap?

Thank to all of you for the suggestion! As a solution I will use a FR4 1.5mm spacer that is around 30kV of insulation so that I can first eliminate the debris problem (thanks I didn't thinked about that) and also augment the lenght of the creepage distance.


bdw Tin whisker growth it's very magical and spooky ahahhahahah those are the hard to find problems ....


Offline TMaxElectronics

  • High Voltage Engineer
  • ****
  • Posts: 297
  • Karma: +23/-0
    • View Profile
    • My random (and very empty) electronics blog
Re: Gap distance between main bus bar
« Reply #8 on: November 07, 2021, 01:44:42 AM »
Quote
bdw Tin whisker growth it's very magical and spooky ahahhahahah those are the hard to find problems ....
especially if they immediately get blown to pieces when they make contact and disappear ;)

Quote
I will use a FR4 1.5mm spacer that is around 30kV of insulation
Yeah that will probably improve the situation without too much effort. But I'm not so sure about the 30kV for 1.5mm FR4. I've seen normal mains (230V) cause tracking from one side of the board to the other before. But that might have been from heat/contamination with smoke machine fluid.

High Voltage Forum

Re: Gap distance between main bus bar
« Reply #8 on: November 07, 2021, 01:44:42 AM »

 


* Recent Topics and Posts

post Re: Capacitor in Parallel with Primary Coil
[Beginners]
Mads Barnkob
Today at 10:17:34 AM
post Capacitor in Parallel with Primary Coil
[Beginners]
FPS
Today at 10:01:41 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
Today at 04:47:35 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
davekni
Today at 03:59:27 AM
post Re: Kaizer VTTC 1
[Vacuum Tube Tesla Coils (VTTC)]
MRMILSTAR
March 28, 2024, 09:15:11 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 28, 2024, 01:01:12 PM
post Re: Big Coil Build Log
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 28, 2024, 05:47:34 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
davekni
March 28, 2024, 04:45:07 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 28, 2024, 04:18:27 AM
post Push Pull VTTC
[Vacuum Tube Tesla Coils (VTTC)]
janno288
March 28, 2024, 01:10:08 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 27, 2024, 10:54:52 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 27, 2024, 11:53:42 AM
post Re: OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 05:14:36 AM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:47:48 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:41:59 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 27, 2024, 12:04:34 AM
post Re: Super flat QCW simulation (does this look reasonable?)
[Dual Resonant Solid State Tesla coils (DRSSTC)]
toooldforthis
March 26, 2024, 11:08:14 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 11:07:20 PM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 10:46:29 PM
post OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 26, 2024, 09:03:43 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 08:46:59 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 26, 2024, 05:02:18 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 03:16:03 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 26, 2024, 01:41:49 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 04:48:22 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 26, 2024, 04:16:37 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 26, 2024, 04:16:24 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 26, 2024, 04:13:02 AM
post Re: CM400 Induction Heater
[Electronic Circuits]
davekni
March 26, 2024, 04:00:43 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
davekni
March 26, 2024, 03:19:18 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
thedoc298
March 26, 2024, 01:50:42 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 08:05:02 PM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 25, 2024, 07:41:29 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 06:45:46 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 05:44:25 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 25, 2024, 04:47:17 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 04:27:22 PM
post Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 25, 2024, 03:57:34 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 25, 2024, 02:06:41 PM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 04:43:25 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
davekni
March 25, 2024, 02:39:40 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 12:47:09 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 24, 2024, 07:36:32 PM
post Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
Alberto
March 24, 2024, 07:27:24 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 24, 2024, 04:25:23 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 10:47:35 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 09:30:21 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 04:34:31 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 03:04:25 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 01:38:34 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 04:20:03 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 23, 2024, 12:54:30 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 23, 2024, 12:05:57 AM
post capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 22, 2024, 11:45:03 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 22, 2024, 11:30:09 PM
post Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 22, 2024, 10:20:35 PM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Benbmw
March 22, 2024, 09:21:13 PM
post Re: What actually kills MOSFETs?
[Beginners]
AstRii
March 22, 2024, 03:37:11 PM
post What actually kills MOSFETs?
[Beginners]
FPS
March 22, 2024, 05:09:20 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 22, 2024, 03:57:54 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 22, 2024, 02:59:25 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 06:31:42 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
rikkitikkitavi
March 21, 2024, 03:08:01 PM
post Re: [WTS] IGBT, Ferrite, Capacitors, Tools, PSU, Industrial components and parts
[Sell / Buy / Trade]
Mads Barnkob
March 21, 2024, 01:37:32 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Alberto
March 21, 2024, 11:42:07 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 21, 2024, 04:09:14 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 02:15:31 AM
post My Homemade Structural Analysis X-Ray Machine
[X-ray]
Luca c.
March 21, 2024, 01:35:40 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 20, 2024, 10:40:00 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Mads Barnkob
March 20, 2024, 08:03:41 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Mads Barnkob
March 20, 2024, 07:51:57 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 20, 2024, 10:39:47 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 20, 2024, 04:09:59 AM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 20, 2024, 01:13:23 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
March 20, 2024, 12:45:16 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 20, 2024, 12:30:30 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 11:12:24 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:47:49 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:44:19 PM
post Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 19, 2024, 06:52:09 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 19, 2024, 05:02:44 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
Mads Barnkob
March 19, 2024, 05:01:41 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 04:31:02 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 03:59:54 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 06:41:39 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 19, 2024, 04:05:49 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 18, 2024, 09:08:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 09:07:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
Twospoons
March 18, 2024, 08:57:06 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
MRMILSTAR
March 18, 2024, 03:51:33 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:59:46 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:33:25 PM
post Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 11:02:12 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Twospoons
March 18, 2024, 02:36:11 AM
post Re: Best forum for vacuum tube amplifiers?
[General Chat]
Mads Barnkob
March 17, 2024, 07:42:55 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:15:14 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 05:05:04 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
davekni
March 17, 2024, 04:50:51 AM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Twospoons
March 17, 2024, 04:45:17 AM
post 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:17:51 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal