Author Topic: VTTC on GU-81M  (Read 4167 times)

Offline Continuum

  • High Voltage Enthusiast
  • *
  • Posts: 3
  • Karma: +0/-0
    • View Profile
VTTC on GU-81M
« on: September 05, 2020, 01:15:54 PM »
Hello! I have been working on this project slowly for about 2 years now, and its finally coming together! Here are some specs: Power supply is two 700W MOTs wired in parallel with a voltage doubler(6uf cap). Its filtered with 2 russian 2.2nf caps connected in parallel, I honestly doubt they really do help in any way, but safety and common sence required me to put them in. The tube has a little filter on the anode, 22 ohms 15W wire wound resistor and about 23 turns of 1mm diameter magnet wire. The resonant cap is two 20kv 2nf caps connected in series, and the primary is wound with 2.5mm^2 wire, 39 turns with taps from the 24th turn upwards. The feedback coil is wound with 1mm diameter wire, 17 turns total with taps from the 12th turn upwards. Currently connected on the 15th turn. With the secondary I went a bit over board I think, its 2000 turns of 0.2mm magnet wire on 10cm diameter pvc pipe. It also has a little topload, about 9.4cm major diameter, 2.4cm minor diameter. Its a standard schematic with the grid leak connected to ground, and the tube is working as a triode. And the grid lieak circuit is a 910Ohm wire wound resistor and a 2nf 10kv cap at the moment. It was fine until i starded powering it with more and more voltage(Im not exceeding the limitations, its just that I previously powered it with half the line voltage). Something made a loud bang, there was a bright flash inside the chassey, and the poor tube died! I couldnt find the fault in the circuit. After doing a bit of research I found out that the tube I used (The Polish version, GU81 without the M) had a capacitor inside the bulb, so maybe that exploded? Later when cranking up the power there was a blue haze inside of the tube, it didnt seem to be gassy, but something was wrong clearly. I replaced the tube, and the same thing happened! The tube survived this time though, but I saw some blue discharges inside it for a second when tha fault happened. Only then I found out that the HV PSU transformer I was using at the time had some shorted turns on the secondary and there was clearly some arcing going on. But that couldnt have caused the loud bang or arcing inside the tube right? I replaced it with the 2 MOTs Im using at the moment, but Im still scared to turn the power up, I really dont want to kill the new tube! What could be causing these issues? What should I do to ensure I wont damage it?
I know the wiring looks messy on the photos, but in person it looks a lot nicer + of course I made sure no wires are touching for safety. Ive attached some photos for reference :)

Offline johnnyzoo

  • High Voltage Enthusiast
  • *
  • Posts: 35
  • Karma: +2/-0
    • View Profile
Re: VTTC on GU-81M
« Reply #1 on: September 06, 2020, 10:16:47 PM »
Please take this with a grain of salt as I'm not very experienced with tube technology, and even less so with tesla coils...

Did you happen to see or hear where the bang happened?

Loud bang + transformer arcing later sounds like a breakdown somewhere (in the transformer, maybe?) followed by a rapid discharge of a capacitor and then steady arcing due to failed insulation.

What kind of transformer were you using before switching to MOTs?

Offline Continuum

  • High Voltage Enthusiast
  • *
  • Posts: 3
  • Karma: +0/-0
    • View Profile
Re: VTTC on GU-81M
« Reply #2 on: September 09, 2020, 12:39:13 AM »
Thanks for the reply!
The transformer I was using previously was a big MOT, I found it on a local faire, it was really massive and rated for 1.4kW.
Sadly I couldnt find the place where the bang happened, so the only suspect is the transformer where there was clearly some arcing. But Im still not sure why did the transformer arc over in the first place(maybe it was damaged right out of the box actually, since I bought in used on a faire for cheap...) + why was there a blue haze in the tube during the fault? I know that happened because I was lucky enough to catch the fault happening on camera, but it was only pointed to the top of the machine, so still no clue what happened inside of the chassey.
I recall putting too many turns on the feedback coil when the fault first happened, I quickly noticed the mistake and reduced the size of that winding. The transformer was already broken by that point, so that explains why the bang happened again even after I reduced the feedback coil.
But why the blue haze inside the tube even after reducing the feedback coil? That indicates either a gassy tube or a significantly too large voltage in it... If only I knew the tube was good! It should be though, maybe I should consider just testing it out of the circuit? In the end, that too I bought on the faire, so I may have just gotten incredibly unlucky and both the transformer and the tube were faulty! Ill try powering the tube up out of the circuit and seeing if it is gassy, and Ill take a closer look to the old transformer that was damaged.

Offline johnnyzoo

  • High Voltage Enthusiast
  • *
  • Posts: 35
  • Karma: +2/-0
    • View Profile
Re: VTTC on GU-81M
« Reply #3 on: September 09, 2020, 11:23:23 AM »
Are there any loose parts or metal chips inside the tube? Of course it will not tell everything, but it is easy to check.

You said there's a capacitor inside the tube. Can you locate it, does it look good or burned?

Good vacuum does not carry sound waves so an explosion inside an intact tube *might* not sound very loud... just my 2 cents.

Offline Mads Barnkob

  • Administrator
  • Executive Board Member
  • *****
  • Posts: 2267
  • Karma: +71/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: VTTC on GU-81M
« Reply #4 on: September 10, 2020, 03:12:39 PM »
I have had problems with arcing inside tube before, seemed to happen between legs at the bottom if they were pushed beyond their voltage rating.

There is no capacitors inside of tubes, perhaps its just ceramic insulators.

Tubes are very forgiving on over-current and will glow red before white and into destruction, but over-voltage is harsh on it, if you have a flash-over between grid and anode, the grid could have been damaged, melted and short-circuit to something, quick flash+bang and its burned away.

Be sure its not just the anode voltage you have to keep in spec, but also the maximum grids to anode/cathode voltages!

https://kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline Continuum

  • High Voltage Enthusiast
  • *
  • Posts: 3
  • Karma: +0/-0
    • View Profile
Re: VTTC on GU-81M
« Reply #5 on: September 21, 2020, 12:18:10 PM »
Sorry for the slow replies - havent had time to work on this project recently.
So in the Polish GU-81 there is a capacitor marked on the datasheet, and I actually can spot something that looks like one in side the glass bulb. Anyway, Im using a GU-81M which doesnt have that, so I guess Im safe for now. There is nothing flying around inside the bulb luckily, no metal or glass or anything :)
I took a look at the old transformer, and there is a spot that looks like it was very hot once - I suppose the flashover happened deeper inside the winding, causing the outer layers to be heated. Should i cut open the winding to check and see if there was a big flashover there? Just to test the hypothesis, Im getting desperate to figure out whats going on here.
Furthermore I looked at the video I took of the fault happening(link below), and slowed it down. The discharges inside the tube happen one frame before the bang happens! So that would indicate, there is a big overvoltage in the system, which first causes the tube to flash internally, and then the transformer follows! What could be the cause of such behaviour?
Link to the video:
/>

Offline johnnyzoo

  • High Voltage Enthusiast
  • *
  • Posts: 35
  • Karma: +2/-0
    • View Profile
Re: VTTC on GU-81M
« Reply #6 on: October 31, 2020, 04:34:52 PM »
Just a note: The fourth attachment in the first post is corrupted. The thumbnail is fine but if you open the full picture, it shows garbage.

Delay of one frame between the flash and audible bang might also have been caused by the camera. I'm pretty sure that the bang was caused by the same event that caused the flash.

Do you have a variable supply transformer to slowly ramp up the voltage?

Measuring the anode and grid voltages with an oscilloscope might reveal something too, but it requires a special high voltage probe and great care.
« Last Edit: October 31, 2020, 04:43:01 PM by johnnyzoo »

Offline Mads Barnkob

  • Administrator
  • Executive Board Member
  • *****
  • Posts: 2267
  • Karma: +71/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: VTTC on GU-81M
« Reply #7 on: November 01, 2020, 10:01:00 AM »
Flash-overs in tube for a VTTC has in my experience been from violating the maximum grid voltage ratings. Your feedback might be too hard, try to lower the coupling or number of windings of the feedback coil.
https://kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

High Voltage Forum

Re: VTTC on GU-81M
« Reply #7 on: November 01, 2020, 10:01:00 AM »

 


* Recent Topics and Posts

post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
Today at 04:47:35 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
davekni
Today at 03:59:27 AM
post Re: Kaizer VTTC 1
[Vacuum Tube Tesla Coils (VTTC)]
MRMILSTAR
March 28, 2024, 09:15:11 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 28, 2024, 01:01:12 PM
post Re: Big Coil Build Log
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 28, 2024, 05:47:34 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
davekni
March 28, 2024, 04:45:07 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 28, 2024, 04:18:27 AM
post Push Pull VTTC
[Vacuum Tube Tesla Coils (VTTC)]
janno288
March 28, 2024, 01:10:08 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 27, 2024, 10:54:52 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 27, 2024, 11:53:42 AM
post Re: OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 05:14:36 AM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:47:48 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:41:59 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 27, 2024, 12:04:34 AM
post Re: Super flat QCW simulation (does this look reasonable?)
[Dual Resonant Solid State Tesla coils (DRSSTC)]
toooldforthis
March 26, 2024, 11:08:14 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 11:07:20 PM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 10:46:29 PM
post OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 26, 2024, 09:03:43 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 08:46:59 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 26, 2024, 05:02:18 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 03:16:03 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 26, 2024, 01:41:49 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 04:48:22 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 26, 2024, 04:16:37 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 26, 2024, 04:16:24 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 26, 2024, 04:13:02 AM
post Re: CM400 Induction Heater
[Electronic Circuits]
davekni
March 26, 2024, 04:00:43 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
davekni
March 26, 2024, 03:19:18 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
thedoc298
March 26, 2024, 01:50:42 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 08:05:02 PM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 25, 2024, 07:41:29 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 06:45:46 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 05:44:25 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 25, 2024, 04:47:17 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 04:27:22 PM
post Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 25, 2024, 03:57:34 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 25, 2024, 02:06:41 PM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 04:43:25 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
davekni
March 25, 2024, 02:39:40 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 12:47:09 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 24, 2024, 07:36:32 PM
post Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
Alberto
March 24, 2024, 07:27:24 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 24, 2024, 04:25:23 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 10:47:35 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 09:30:21 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 04:34:31 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 03:04:25 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 01:38:34 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 04:20:03 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 23, 2024, 12:54:30 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 23, 2024, 12:05:57 AM
post capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 22, 2024, 11:45:03 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 22, 2024, 11:30:09 PM
post Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 22, 2024, 10:20:35 PM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Benbmw
March 22, 2024, 09:21:13 PM
post Re: What actually kills MOSFETs?
[Beginners]
AstRii
March 22, 2024, 03:37:11 PM
post What actually kills MOSFETs?
[Beginners]
FPS
March 22, 2024, 05:09:20 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 22, 2024, 03:57:54 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 22, 2024, 02:59:25 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 06:31:42 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
rikkitikkitavi
March 21, 2024, 03:08:01 PM
post Re: [WTS] IGBT, Ferrite, Capacitors, Tools, PSU, Industrial components and parts
[Sell / Buy / Trade]
Mads Barnkob
March 21, 2024, 01:37:32 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Alberto
March 21, 2024, 11:42:07 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 21, 2024, 04:09:14 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 02:15:31 AM
post My Homemade Structural Analysis X-Ray Machine
[X-ray]
Luca c.
March 21, 2024, 01:35:40 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 20, 2024, 10:40:00 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Mads Barnkob
March 20, 2024, 08:03:41 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Mads Barnkob
March 20, 2024, 07:51:57 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 20, 2024, 10:39:47 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 20, 2024, 04:09:59 AM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 20, 2024, 01:13:23 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
March 20, 2024, 12:45:16 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 20, 2024, 12:30:30 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 11:12:24 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:47:49 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:44:19 PM
post Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 19, 2024, 06:52:09 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 19, 2024, 05:02:44 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
Mads Barnkob
March 19, 2024, 05:01:41 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 04:31:02 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 03:59:54 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 06:41:39 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 19, 2024, 04:05:49 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 18, 2024, 09:08:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 09:07:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
Twospoons
March 18, 2024, 08:57:06 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
MRMILSTAR
March 18, 2024, 03:51:33 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:59:46 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:33:25 PM
post Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 11:02:12 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Twospoons
March 18, 2024, 02:36:11 AM
post Re: Best forum for vacuum tube amplifiers?
[General Chat]
Mads Barnkob
March 17, 2024, 07:42:55 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:15:14 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 05:05:04 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
davekni
March 17, 2024, 04:50:51 AM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Twospoons
March 17, 2024, 04:45:17 AM
post 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:17:51 AM
post Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Terry
March 17, 2024, 01:29:32 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 17, 2024, 12:33:06 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal