Author Topic: Benjamin's DRSSTC3  (Read 2518 times)

Offline Benjamin Lockhart

  • High Voltage Experimenter
  • **
  • Posts: 96
  • Karma: +12/-0
    • View Profile
Benjamin's DRSSTC3
« on: November 27, 2023, 09:07:43 AM »
Hi all,
After having problems with the driver dying in my large freewheeling coil, I decided that I wasn't happy with the overall design. It's too heavy and difficult to set up. So I built a whole new coil.
The plywood base is 16.75 inches in diameter and the whole coil stands about 5 feet tall

It's based heavily on Loneoceans DRSSTC3, and just so happens to be my 3rd coil build.
The specs are;
   8x36 inch chicken wire and plywood toroid (it's a cheap way to build), with 3.25x14 inch smaller toroid below
   6.3x27.5 inch secondary with 28AWG wire

   8 turn primary of 1/4 inch tube with 3/16 inch between turns and 0.8 inch clearance from secondary, 0.162 coupling, compressed air cooled, but I may need to upgrade to water cooling, I was melting primary supports! Edit: this has been done.

   365nF 15kV 260A rms MMC using dawncaps, it stays completely cold. Javatc says the primary surge impedance is about 7.5 ohms and I think that number has quite an effect on the behavior of spark growth. Also I think that the primary and secondary geometry is more important than the exact coupling, however you should still try to maximize coupling for a given geometry. Play around with the primary outer diameter in javatc, you will find that there is a sweet spot that gives the most coupling. The exact diameter depends on other parameters as well.

   UD2.7C

   800A OCD for now, primary current peaks around 1000A
   130uS on time
   CM300du-24nfh full bridge, 680V DC bus voltage
   Approx 60kHz operating frequency with 7% primary detuning.


   4x 3300uF, 450V bus capacitors in doubler for 3300uF total, not shown are 2uF snubber caps across each IGBT brick.


   Onboard bus precharge circuit consisting of a 12 ohm resistor that gets bypassed by a 50A relay powered by the 24V SMPS. The SMPS has a 1/4 second turn- on delay which is enough for the caps to almost fully charge before the relay closes.

Here are some build pictures.



I don't know why some pictures are sideways?

Here is a tin can almost melting at half voltage.
And it makes 7 foot sparks! (edit: now 8.5 feet!)



The sparks really are incredibly bright!
What do you all think?
« Last Edit: May 28, 2024, 05:17:44 AM by Benjamin Lockhart »

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2820
  • Karma: +134/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: Benjamin's DRSSTC3
« Reply #1 on: November 29, 2023, 06:32:03 AM »
Quote
What do you all think?
Looks like a very clean build with great performance!

Quote
Approx 60kHz operating frequency with 7% primary detuning.
Would have guessed you'd want a bit more than 7% for long arcs.  Arc length is already good.  Top load size helps with minimizing detuning, and coupling helps maintain performance in spite of secondary frequency drop.  That may be why 7% is sufficient.  Probably best for music.  Would be interesting to see if arc length could be any longer with a bit more detuning and a bit longer on time.  That's only if you want to risk pushing coil's limits.
David Knierim

Offline Benjamin Lockhart

  • High Voltage Experimenter
  • **
  • Posts: 96
  • Karma: +12/-0
    • View Profile
Re: Benjamin's DRSSTC3
« Reply #2 on: March 30, 2024, 08:03:00 AM »
I just ran the coil again and everything went well.
I made a shielded 10 gauge power cord for it and put a strike protection wire around the coil base.


/>
/>
/>

Offline Benjamin Lockhart

  • High Voltage Experimenter
  • **
  • Posts: 96
  • Karma: +12/-0
    • View Profile
Re: Benjamin's DRSSTC3
« Reply #3 on: May 27, 2024, 09:44:40 PM »
I've got an interesting update now. The coil has hit 8.5 foot (2.6 meter) sparks! with a new toroid and the same tap point. I think it's around 10% detuning maybe a bit less, which still plays midi very nicely! These are video frames of an 8.5 foot ground strike! This is 3.7x the winding length while playing music which is amazing for a regular non pulse skipping DRSSTC!

For reference the specs are, 800A ocd, 120us on time, 680V bus, 8" x 36" toroid, 0.365uF MMC, 7.3 ohm primary surge impedance, 60kHz primary fres. Otherwise it's exactly Loneoceans DRSSTC3 specs.





I made a nice skeleton toroid because I was tired of the chicken wire bending out of shape. It's 8" x 36", the same size as the old one, with 15 rings of 3/8" aluminum fuel line and a welded aluminum frame.



« Last Edit: May 28, 2024, 11:38:09 PM by Benjamin Lockhart »

Offline Michelle_

  • High Voltage Technician
  • ***
  • Posts: 180
  • Karma: +2/-0
    • View Profile
Re: Benjamin's DRSSTC3
« Reply #4 on: May 27, 2024, 10:28:56 PM »
Nice toroid

Offline Benjamin Lockhart

  • High Voltage Experimenter
  • **
  • Posts: 96
  • Karma: +12/-0
    • View Profile
Re: Benjamin's DRSSTC3
« Reply #5 on: May 27, 2024, 11:20:30 PM »
Here's the video. Longest strike at 42 seconds.
« Last Edit: May 27, 2024, 11:22:23 PM by Benjamin Lockhart »

Offline Jj

  • High Voltage Enthusiast
  • *
  • Posts: 5
  • Karma: +0/-0
    • View Profile
Re: Benjamin's DRSSTC3
« Reply #6 on: May 28, 2024, 01:00:04 PM »
Super results! Does the OCD trigger much?

Online Mads Barnkob

  • Administrator
  • Executive Board Member
  • *****
  • Posts: 2299
  • Karma: +73/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Benjamin's DRSSTC3
« Reply #7 on: May 28, 2024, 02:35:42 PM »
Congratulations on your very well-built coil!

So its free-wheeling, but not pulse skipping? What is the maximum on-time for that MIDI? You must be pushing it hard! :D
https://kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline Benjamin Lockhart

  • High Voltage Experimenter
  • **
  • Posts: 96
  • Karma: +12/-0
    • View Profile
Re: Benjamin's DRSSTC3
« Reply #8 on: May 28, 2024, 07:25:56 PM »
Thank you! The OCD does trigger most of the time so I could even raise it a bit higher than 800A but I'd rather it live a long time.

The on-time was limited to 120us for that run! The duty cycle limit on the midistick interrupter was set to 8% I'm not actually pushing things that hard. That is about 7 RF cycles at 60kHz and the on-time fits within the first notch of the primary current envelope.

It's not freewheeling or pulse skipping, just a regular UD2.7C with the UVLO fix Davekni suggested using a 1.25V shunt regulator.
« Last Edit: June 01, 2024, 11:10:30 PM by Benjamin Lockhart »

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2820
  • Karma: +134/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: Benjamin's DRSSTC3
« Reply #9 on: May 30, 2024, 03:52:36 AM »
Quote
I've got an interesting update now. The coil has hit 8.5 foot (2.6 meter) sparks! with a new toroid and the same tap point. I think it's around 10% detuning maybe a bit less, which still plays midi very nicely! These are video frames of an 8.5 foot ground strike! This is 3.7x the winding length while playing music which is amazing for a regular non pulse skipping DRSSTC!
Very impressive results!  Beautiful top load too.  (I rarely get more than 2m when tuned for good MIDI performance.)
David Knierim

Offline Benjamin Lockhart

  • High Voltage Experimenter
  • **
  • Posts: 96
  • Karma: +12/-0
    • View Profile
Re: Benjamin's DRSSTC3
« Reply #10 on: May 30, 2024, 07:04:40 AM »
Thanks Dave, I believe my relatively large toroid (1.3x secondary length), and high-ish coupling (0.162), combined with a primary surge impedance that's not too high or low, and a relatively high bus voltage for the size of the coil, are all responsible for good performance.

I still haven't seen a single racing spark and I think that's because the primary impedance isn't too low, as well as the big toroid keeping the topload voltage lower

I realize I'm generalizing here without actual numbers other than my coil's specs, feel free to correct my thinking here or add your thoughts!

It does seem like the most efficient mode of DRSSTC operation is transient with the on-time equaling one beat in the primary current. Of course, the coil needs to be optimized to run well with that on-time.

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2820
  • Karma: +134/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: Benjamin's DRSSTC3
« Reply #11 on: May 30, 2024, 10:24:35 PM »
Quote
Thanks Dave, I believe my relatively large toroid (1.3x secondary length), and high-ish coupling (0.162)
Yes, I'd guess those two are the most important factors.  Built my DRSSTC just before finding this forum.  Didn't have a good idea of what to target.  Great work!
David Knierim

Offline Jj

  • High Voltage Enthusiast
  • *
  • Posts: 5
  • Karma: +0/-0
    • View Profile
Re: Benjamin's DRSSTC3
« Reply #12 on: June 10, 2024, 01:36:41 PM »
Thank you! The OCD does trigger most of the time so I could even raise it a bit higher than 800A but I'd rather it live a long time.

The on-time was limited to 120us for that run! The duty cycle limit on the midistick interrupter was set to 8% I'm not actually pushing things that hard. That is about 7 RF cycles at 60kHz and the on-time fits within the first notch of the primary current envelope.

It's not freewheeling or pulse skipping, just a regular UD2.7C with the UVLO fix Davekni suggested using a 1.25V shunt regulator.

I’ve never been able achieve even the same result with long on times compared to short. My coil which is of similar size to yours, but runs much lower at 45kHz has made a best of 1.7M with 120us and a 5 Ohm primary impedance. At that point it had some pretty violent racing arcs and flashovers. Reducing the coupling to .15 didn’t help. So I thought I’d try longer on times again. I increased the primary impedance to 9 ohms and ran all the way up to 320us. The power draw doubled, but streamer length decreased to 1.3m at best. I ran the primary from so low it would hardly break out to something around fpri =fsec with complete notches. Also tried raising the break rate.  Would love to know how those that have success with long on times don’t it! My setups secondary impedance according to Javatc is around 72kOhm which I take it would be considered on the high side, maybe that is the reason?

Offline flyingperson23

  • High Voltage Technician
  • ***
  • Posts: 157
  • Karma: +5/-2
  • noob :)
    • View Profile
Re: Benjamin's DRSSTC3
« Reply #13 on: June 10, 2024, 03:35:28 PM »
I get good (enough) results with long on times by running low bus voltage and pumping tons of power into it without caring about effeciency

Offline Benjamin Lockhart

  • High Voltage Experimenter
  • **
  • Posts: 96
  • Karma: +12/-0
    • View Profile
Re: Benjamin's DRSSTC3
« Reply #14 on: June 10, 2024, 08:08:04 PM »
Yeah, if you care about efficiency, as in max spark length per input power, then short on-times are the best way. The good performing long on time coils I have seen usually use on-times up above 1ms at least. and they draw tons of power.

The big benefit with that is getting long arcs at low pulse rates or even single shot.

High Voltage Forum

Re: Benjamin's DRSSTC3
« Reply #14 on: June 10, 2024, 08:08:04 PM »

 


* Recent Topics and Posts

post Re: Steve Ward's DRSSTC Interrupter stops working when adjusting pulse width
[Electronic Circuits]
petespaco
Today at 04:52:08 PM
post Re: Turning SSTC into DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
Today at 02:14:17 AM
post Re: Turning SSTC into DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
June 12, 2024, 11:04:57 PM
post Turning SSTC into DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
June 12, 2024, 10:23:08 PM
post Re: UD2.7C constantly in OCP despite having signal
[Dual Resonant Solid State Tesla coils (DRSSTC)]
verliebt_in_neukölln17
June 12, 2024, 08:41:06 PM
post Re: UD2.7C constantly in OCP despite having signal
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
June 12, 2024, 07:53:31 PM
post Re: Van de Graaf Voltage measurement with voltage sensor and voltage divider
[Static Electricity]
haversin
June 12, 2024, 06:57:13 PM
post UD2.7C constantly in OCP despite having signal
[Dual Resonant Solid State Tesla coils (DRSSTC)]
verliebt_in_neukölln17
June 12, 2024, 06:54:49 PM
post Re: Van de Graaf Voltage measurement with voltage sensor and voltage divider
[Static Electricity]
Mads Barnkob
June 12, 2024, 03:47:28 PM
post Van de Graaf Voltage measurement with voltage sensor and voltage divider
[Static Electricity]
vK
June 12, 2024, 03:42:18 AM
post Re: Bigger sparks?...
[Vacuum Tube Tesla Coils (VTTC)]
davekni
June 12, 2024, 03:32:22 AM
post Re: Bigger sparks?...
[Vacuum Tube Tesla Coils (VTTC)]
Teslaventje
June 11, 2024, 11:05:49 PM
post Re: Bigger sparks?...
[Vacuum Tube Tesla Coils (VTTC)]
MRMILSTAR
June 11, 2024, 05:36:46 AM
post Re: Sling Psychrometer
[Laboratories, Equipment and Tools]
Twospoons
June 11, 2024, 12:29:31 AM
post Bigger sparks?...
[Vacuum Tube Tesla Coils (VTTC)]
Teslaventje
June 10, 2024, 11:05:55 PM
post Re: Syntherrupter - A Feature-rich, Polyphonic Interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Max
June 10, 2024, 10:57:51 PM
post Re: Benjamin's DRSSTC3
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
June 10, 2024, 08:08:04 PM
post Re: Plasma Torid - Class E Self Resonant Dual/Stereo - Plasma Torid Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hi-Deff
June 10, 2024, 06:04:09 PM
post Sling Psychrometer
[Laboratories, Equipment and Tools]
klugesmith
June 10, 2024, 04:43:59 PM
post Re: Benjamin's DRSSTC3
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
June 10, 2024, 03:35:28 PM
post Re: Benjamin's DRSSTC3
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Jj
June 10, 2024, 01:36:41 PM
post Re: Is a 60UF 800VDC Dawncap good for an induction heater?
[General Chat]
Anders Mikkelsen
June 09, 2024, 05:44:29 PM
post Is a 60UF 800VDC Dawncap good for an induction heater?
[General Chat]
yourboi
June 09, 2024, 03:31:30 PM
post Re: Steve Ward's DRSSTC Interrupter stops working when adjusting pulse width
[Electronic Circuits]
NyaaX_X
June 09, 2024, 01:34:49 PM
post Steve Ward's DRSSTC Interrupter stops working when adjusting pulse width
[Electronic Circuits]
verliebt_in_neukölln17
June 09, 2024, 01:56:51 AM
post Re: Return of Electronics Flea Market in "Silicon Valley"
[Sell / Buy / Trade]
klugesmith
June 08, 2024, 06:06:25 AM
post Re: Coulometric hourmeters
[Laboratories, Equipment and Tools]
klugesmith
June 08, 2024, 05:38:14 AM
post Interrupter for SSTC
[Beginners]
Simranjit
June 08, 2024, 12:47:47 AM
post Re: Adding capacitor to primary in SSTC
[Solid State Tesla Coils (SSTC)]
Michelle_
June 07, 2024, 03:59:57 PM
post Re: Adding capacitor to primary in SSTC
[Solid State Tesla Coils (SSTC)]
davekni
June 07, 2024, 06:42:26 AM
post Re: Space-X Starship test this week
[Science, Research and News In Other Fields Than Electronics]
MRMILSTAR
June 07, 2024, 05:08:00 AM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
davekni
June 07, 2024, 03:16:31 AM
post Re: Space-X Starship test this week
[Science, Research and News In Other Fields Than Electronics]
klugesmith
June 06, 2024, 11:37:20 PM
post Adding capacitor to primary in SSTC
[Solid State Tesla Coils (SSTC)]
Simranjit
June 06, 2024, 11:20:23 PM
post Re: Plasma Torid - Class E Self Resonant Dual/Stereo - Plasma Torid Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
June 06, 2024, 10:54:48 PM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
ZakW
June 06, 2024, 05:17:02 AM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
Simranjit
June 06, 2024, 04:50:00 AM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
davekni
June 06, 2024, 04:00:52 AM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
ZakW
June 06, 2024, 01:43:41 AM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
Simranjit
June 05, 2024, 11:11:17 PM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
Michelle_
June 05, 2024, 10:18:57 PM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
Simranjit
June 05, 2024, 10:13:03 PM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
ZakW
June 05, 2024, 09:29:18 PM
post Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
Simranjit
June 05, 2024, 08:46:53 PM
post Re: Want to build HV HF oscilloscope probe.
[Electronic Circuits]
Twospoons
June 05, 2024, 07:04:45 AM
post Re: Want to build HV HF oscilloscope probe.
[Electronic Circuits]
Domo
June 05, 2024, 04:58:35 AM
post Re: Pearson current monitor model 1330 teardown (100kA)
[Laboratories, Equipment and Tools]
klugesmith
June 05, 2024, 01:42:04 AM
post Re: Coulometric hourmeters
[Laboratories, Equipment and Tools]
klugesmith
June 04, 2024, 10:31:58 PM
post Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
pete_dl
June 04, 2024, 08:08:28 PM
post Re: Want to build HV HF oscilloscope probe.
[Electronic Circuits]
Twospoons
June 03, 2024, 11:13:26 PM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
June 03, 2024, 10:35:57 PM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hi-Deff
June 03, 2024, 05:51:05 PM
post Re: Want to build HV HF oscilloscope probe.
[Electronic Circuits]
Domo
June 03, 2024, 07:41:41 AM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
June 03, 2024, 05:28:44 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
June 03, 2024, 05:02:19 AM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
June 03, 2024, 03:47:33 AM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
June 03, 2024, 02:23:58 AM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hi-Deff
June 03, 2024, 01:25:24 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
June 03, 2024, 01:08:47 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
June 02, 2024, 10:29:02 PM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Michelle_
June 02, 2024, 10:02:45 PM
post Re: Racing sparks
[Spark Gap Tesla Coils (SGTC)]
davekni
June 02, 2024, 08:25:37 PM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Michelle_
June 02, 2024, 04:51:58 PM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Michelle_
June 02, 2024, 04:44:30 PM
post Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
MRMILSTAR
June 02, 2024, 03:25:11 PM
post APC Smart-UPS 1500VA Teardown
[Electronic Circuits]
Mads Barnkob
June 02, 2024, 01:36:11 PM
post Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
pete_dl
June 02, 2024, 11:43:40 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
June 02, 2024, 08:49:11 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
June 02, 2024, 08:36:07 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
June 02, 2024, 12:41:50 AM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Benjamin Lockhart
June 01, 2024, 08:24:35 PM
post Pearson current monitor model 1330 teardown (100kA)
[Laboratories, Equipment and Tools]
Mads Barnkob
June 01, 2024, 08:22:28 PM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Michelle_
June 01, 2024, 03:56:53 AM
post Re: Racing sparks
[Spark Gap Tesla Coils (SGTC)]
Terry
June 01, 2024, 12:03:50 AM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hi-Deff
May 31, 2024, 11:46:20 PM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Michelle_
May 31, 2024, 06:13:59 PM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
May 31, 2024, 01:55:22 AM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
May 30, 2024, 11:57:49 PM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
May 30, 2024, 11:50:06 PM
post First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hi-Deff
May 30, 2024, 11:23:35 PM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
davekni
May 30, 2024, 10:43:06 PM
post Re: Benjamin's DRSSTC3
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
May 30, 2024, 10:24:35 PM
post Re: SSTC tripping circuit breaker
[Solid State Tesla Coils (SSTC)]
NyaaX_X
May 30, 2024, 06:10:04 PM
post Re: SSTC tripping circuit breaker
[Solid State Tesla Coils (SSTC)]
Simranjit
May 30, 2024, 04:56:11 PM
post Re: SSTC tripping circuit breaker
[Solid State Tesla Coils (SSTC)]
Michelle_
May 30, 2024, 04:48:05 PM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Michelle_
May 30, 2024, 04:37:22 PM
post Re: SSTC tripping circuit breaker
[Solid State Tesla Coils (SSTC)]
klugesmith
May 30, 2024, 04:16:31 PM
post Re: SSTC tripping circuit breaker
[Solid State Tesla Coils (SSTC)]
NyaaX_X
May 30, 2024, 03:34:10 PM
post Re: SSTC tripping circuit breaker
[Solid State Tesla Coils (SSTC)]
Simranjit
May 30, 2024, 02:53:50 PM
post Re: SSTC tripping circuit breaker
[Solid State Tesla Coils (SSTC)]
NyaaX_X
May 30, 2024, 12:44:47 PM
post SSTC tripping circuit breaker
[Solid State Tesla Coils (SSTC)]
Simranjit
May 30, 2024, 07:52:56 AM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
NyaaX_X
May 30, 2024, 07:07:53 AM
post Re: Benjamin's DRSSTC3
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
May 30, 2024, 07:04:40 AM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Michelle_
May 30, 2024, 05:16:50 AM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Michelle_
May 30, 2024, 05:08:17 AM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
davekni
May 30, 2024, 04:29:30 AM
post Re: Benjamin's DRSSTC3
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
May 30, 2024, 03:52:36 AM
post Re: Racing sparks
[Spark Gap Tesla Coils (SGTC)]
davekni
May 30, 2024, 03:47:12 AM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Benjamin Lockhart
May 30, 2024, 03:41:34 AM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Michelle_
May 30, 2024, 03:27:28 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal