Author Topic: Slow rise & fall time  (Read 15000 times)

Offline Laci

  • High Voltage Engineer
  • ****
  • Posts: 214
  • Karma: +6/-0
    • View Profile
Re: Slow rise & fall time
« Reply #20 on: August 13, 2018, 10:20:43 PM »
So I finished the building of my new coil,the resonant frequency is around 170kHz as the JavaTC calculated.Today I put everything together and started testing.Sadly it performs as badly as before-nowhere near in comparision with a halfbridge design.The input voltage was more than 50V,but it was drawing over 4A even at 20V in CW mode,with some mm weak arcs.At the 50V supply I had a 4700uF smoothing capacitor,which discharged really fast in interrupted mode,when the supply(transformer)was turned off.I suppose there are huge losses,probably at the points that I marked before.Tomorrow I will make some more test,maybe measuring the inverter output,gate drive waveforms vs input current(through a shunt resistor).

The ferrite bead you are talking about is something like this?


I have a similar thing salvaged from an angle grinder,sadly nothing else.

A picture of the current setup:
« Last Edit: August 13, 2018, 10:25:30 PM by Laci »

Offline T3sl4co1l

  • High Voltage Technician
  • ***
  • Posts: 174
  • Karma: +9/-0
    • View Profile
    • Seven Transistor Labs
Re: Slow rise & fall time
« Reply #21 on: August 16, 2018, 07:59:03 AM »
Just to clarify for this example we are talking about the MI1206L391R.  Is the 300mA saturation a derived value?  I did not see it listed but I could have missed it.

Yes. See where the impedance at 100MHz drops to 70% of the zero bias figure.  You'll have to roughly interpolate the curves they give.  The real value is somewhere around there.


Quote
When I look at its impedance graph, I see the impedance tends towards 0 below 1MHz.  To me this is saying there is little power dissipation below 1Mhz so temperature should not be an issue?  The ringing we want to get rid of is in the low to 10s of MHz but the amount of energy in the ringing should be far less than the signal.

Ah, but we are driving gates here, so the current waveform is very peaky, the derivative of a square wave (approximately)!

I have a project that runs FDP33N25s (Qg = 37nC typ.) at up to 2MHz, with a small ferrite bead (might've been Fair-Rite #2673000101?) on the gate, and they get warm!  Not up to Tc, though.  I've cooked (up to Tc) the same size beads, in #43 material, on the S or D leads of STP19NM50s without any load at all (just commutation current: also very peaky, but much sharper, more intense, than gate drive!)

More specifically: an H bridge, hard switching, no load current, 300kHz, 320VDC supply.  So, just charging Coss through stray inductance and ferrite beads.

Quote
I agree the current limit of 2 amps is the limit and this cannot be exceeded.  The package is only so big...

Which, again, is only a thermal rating, for some typical test condition.  You're welcome to run hotter, at risk of cracking or oxidation.  Or maybe you can't handle the losses, and you need to run less, anyway.

And core loss directly impacts the current rating, just as it does for regular inductors.  It might be rated 2A at DC, but 1A when, say, 300mA (RMS) at 1MHz is also applied, or whatever.  Or it might be 3A (DC) with generous copper pours, or less with minimal footprints.

Quote
I sent an email off to a contact at Laird to ask them for their opinion.  I will post the response if I get one.

Cool, will like to hear. :)

Tim

Offline Teravolt

  • High Voltage Technician
  • ***
  • Posts: 125
  • Karma: +2/-0
    • View Profile
Re: Slow rise & fall time
« Reply #22 on: August 20, 2018, 02:29:41 AM »
hi Laci, I don't know if you got this problem solved or not but what I am seeing in these pictures is shoot through. if it were me I would add dead time that is a little grater than your 560ns rise and fall times like 1us. If this happens with your main bridge it will be undesirable. If you drive each mosfet directly with a driver with 1-3 ohms. I found this

http://omapalvelin.homedns.org/tesla/SSTC/half-bridge.htm
http://www.modularcircuits.com/blog/articles/h-bridge-secrets/h-bridge-control/
http://www.loneoceans.com/labs/ud27/

hope this helps

Offline Laci

  • High Voltage Engineer
  • ****
  • Posts: 214
  • Karma: +6/-0
    • View Profile
Re: Slow rise & fall time
« Reply #23 on: August 20, 2018, 10:37:37 PM »
Hi Teravolt!Thanks for the useful informations!The coil is working well yet,I have not tested it at high power,but it is already too noisy to run indoors.I am planning to modify the current oneTesla interrupter to add a mains synced staccato controller to it for long and more quiet sparks.
The waveform is the same as before,a bit high rise and fall time.One thing I figured out is that there is no problem with the gate resistors,since the fall time is also high through the gate schottky diodes.I suppose my ferrite core is not the best in my situation.The deadtime is a great idea,not sure if I have enough empty space on the driver board for some more components.Hopefully the 440V TVS and MUR1560 duo will prevent the IGBTs from dangerous overshoots! :)

Offline TDAF

  • High Voltage Technician
  • ***
  • Posts: 108
  • Karma: +4/-0
    • View Profile
Re: Slow rise & fall time
« Reply #24 on: August 21, 2018, 03:09:01 AM »
I don't think there's a need to add the MURs as the IGBTs already come with built-in diodes which are much more optimized for the task at hand

I would not suggest you to go for that

Offline Laci

  • High Voltage Engineer
  • ****
  • Posts: 214
  • Karma: +6/-0
    • View Profile
Re: Slow rise & fall time
« Reply #25 on: August 21, 2018, 07:51:31 AM »
I have IRG4PC60U's which do not have built in diode.The 440V TVS diodes should be enough,I just keep them for safety against my high inductance bridge design.:P

Offline TDAF

  • High Voltage Technician
  • ***
  • Posts: 108
  • Karma: +4/-0
    • View Profile
Re: Slow rise & fall time
« Reply #26 on: August 21, 2018, 06:46:11 PM »
Oh, oops
Should've read the intro post!

Anyways then I definitely recommend the MURs

High Voltage Forum

Re: Slow rise & fall time
« Reply #26 on: August 21, 2018, 06:46:11 PM »

 


* Recent Topics and Posts

post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
Today at 04:47:35 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
davekni
Today at 03:59:27 AM
post Re: Kaizer VTTC 1
[Vacuum Tube Tesla Coils (VTTC)]
MRMILSTAR
March 28, 2024, 09:15:11 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 28, 2024, 01:01:12 PM
post Re: Big Coil Build Log
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 28, 2024, 05:47:34 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
davekni
March 28, 2024, 04:45:07 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 28, 2024, 04:18:27 AM
post Push Pull VTTC
[Vacuum Tube Tesla Coils (VTTC)]
janno288
March 28, 2024, 01:10:08 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 27, 2024, 10:54:52 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 27, 2024, 11:53:42 AM
post Re: OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 05:14:36 AM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:47:48 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:41:59 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 27, 2024, 12:04:34 AM
post Re: Super flat QCW simulation (does this look reasonable?)
[Dual Resonant Solid State Tesla coils (DRSSTC)]
toooldforthis
March 26, 2024, 11:08:14 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 11:07:20 PM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 10:46:29 PM
post OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 26, 2024, 09:03:43 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 08:46:59 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 26, 2024, 05:02:18 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 03:16:03 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 26, 2024, 01:41:49 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 04:48:22 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 26, 2024, 04:16:37 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 26, 2024, 04:16:24 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 26, 2024, 04:13:02 AM
post Re: CM400 Induction Heater
[Electronic Circuits]
davekni
March 26, 2024, 04:00:43 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
davekni
March 26, 2024, 03:19:18 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
thedoc298
March 26, 2024, 01:50:42 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 08:05:02 PM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 25, 2024, 07:41:29 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 06:45:46 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 05:44:25 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 25, 2024, 04:47:17 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 04:27:22 PM
post Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 25, 2024, 03:57:34 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 25, 2024, 02:06:41 PM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 04:43:25 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
davekni
March 25, 2024, 02:39:40 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 12:47:09 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 24, 2024, 07:36:32 PM
post Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
Alberto
March 24, 2024, 07:27:24 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 24, 2024, 04:25:23 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 10:47:35 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 09:30:21 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 04:34:31 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 03:04:25 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 01:38:34 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 04:20:03 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 23, 2024, 12:54:30 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 23, 2024, 12:05:57 AM
post capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 22, 2024, 11:45:03 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 22, 2024, 11:30:09 PM
post Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 22, 2024, 10:20:35 PM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Benbmw
March 22, 2024, 09:21:13 PM
post Re: What actually kills MOSFETs?
[Beginners]
AstRii
March 22, 2024, 03:37:11 PM
post What actually kills MOSFETs?
[Beginners]
FPS
March 22, 2024, 05:09:20 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 22, 2024, 03:57:54 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 22, 2024, 02:59:25 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 06:31:42 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
rikkitikkitavi
March 21, 2024, 03:08:01 PM
post Re: [WTS] IGBT, Ferrite, Capacitors, Tools, PSU, Industrial components and parts
[Sell / Buy / Trade]
Mads Barnkob
March 21, 2024, 01:37:32 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Alberto
March 21, 2024, 11:42:07 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 21, 2024, 04:09:14 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 02:15:31 AM
post My Homemade Structural Analysis X-Ray Machine
[X-ray]
Luca c.
March 21, 2024, 01:35:40 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 20, 2024, 10:40:00 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Mads Barnkob
March 20, 2024, 08:03:41 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Mads Barnkob
March 20, 2024, 07:51:57 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 20, 2024, 10:39:47 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 20, 2024, 04:09:59 AM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 20, 2024, 01:13:23 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
March 20, 2024, 12:45:16 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 20, 2024, 12:30:30 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 11:12:24 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:47:49 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:44:19 PM
post Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 19, 2024, 06:52:09 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 19, 2024, 05:02:44 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
Mads Barnkob
March 19, 2024, 05:01:41 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 04:31:02 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 03:59:54 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 06:41:39 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 19, 2024, 04:05:49 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 18, 2024, 09:08:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 09:07:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
Twospoons
March 18, 2024, 08:57:06 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
MRMILSTAR
March 18, 2024, 03:51:33 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:59:46 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:33:25 PM
post Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 11:02:12 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Twospoons
March 18, 2024, 02:36:11 AM
post Re: Best forum for vacuum tube amplifiers?
[General Chat]
Mads Barnkob
March 17, 2024, 07:42:55 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:15:14 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 05:05:04 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
davekni
March 17, 2024, 04:50:51 AM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Twospoons
March 17, 2024, 04:45:17 AM
post 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:17:51 AM
post Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Terry
March 17, 2024, 01:29:32 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 17, 2024, 12:33:06 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal