This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Unleashed
Pages: [1]
1
« on: May 11, 2017, 08:18:02 AM »
Hey Mads, a little update. My coil is acting completely weird, I'll try to sum it up as best as I can. I wired it up and I wasn't getting anytning, no power drawn, nothing. Moving the antenna around however did change something. For some reason, the only way I can get the coil to do something (and it's just a small corona) is by having the antenna extremely close to the breakout point, so close that it'll just arc into it, which is weird. But the weirdest behavior was that once I turned off the variac for tests, as soon as I would touch anything (I even got shocked), the coil would fire a small spark. Even touching the main smoothing capacitor with the multimeter terminals did that. Thoughts ?
2
« on: May 06, 2017, 05:59:23 PM »
Hey Mads, thank you so much for your help. The first picture is just the GDT connected to the mosfets, without a load on them, the second one is the same thing, except I have a resistor where the primary should be, instead of having it open. Also, correct me if I'm wrong, shouldn't the bottom edges be the same as the top ones?
3
« on: May 06, 2017, 03:19:08 PM »
Ok, I adjusted the duty cycle, this is what I get No load Resistive load
4
« on: May 06, 2017, 01:52:57 PM »
Hey Mads, thank you for the reply. You're perfectly right, I completely forgot about adjusting the duty cycle. I'm using a 555 oscillator to simulate the antenna, I'll definitely lower it to 50% and give it another try. As for my setup, here's a picture. I was powering it at around 15V from my power supply, with a 12ohm 5W resistor. The measurements have been carried out with all the GDT terminals connected to the mosfets, and the oscilloscope was hooked between gate and source of one of the mosfets.
5
« on: May 05, 2017, 11:06:39 PM »
Well, first of all, hi everyone, and hi Mads! Been a fan of your work for a while, hence why i'm trying to make a teslacoil based on your SSTC II project. So far I've wound the coil, assembled the driver circuit on breadboard, and assembled the full bridge. I haven't done too much testing, but I'm trying to get the GDT waveform right. The tests I've done so far included varying the damping resistors and GDT inductance, by going from 15 turns to 20, did improve it a bit, from this to this: The core I'm using is an N30 core, with around 4800 mH of magnetic permeability. The waveform also seems to change a little with a slight resistive load (around 2A) on the bridge, from the one above to this (which correct me if I'm wrong, is unusable). This is the waveform i get when the GDT is not connected to the bridge I think the problem might be a low GDT inductance. Any suggestions?
Pages: [1]
Recent Topics and Posts
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Benjamin Lockhart Today at 06:33:37 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ Today at 05:45:04 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Benjamin Lockhart Today at 05:34:16 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ Today at 04:50:57 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Benjamin Lockhart Today at 04:03:55 AM
|
|
Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Benjamin Lockhart Today at 02:35:56 AM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
Bobakman April 19, 2024, 09:37:52 PM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
klugesmith April 19, 2024, 09:20:10 PM
|
|
Re: Next Gen DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Mads Barnkob April 19, 2024, 07:22:26 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 19, 2024, 04:46:36 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
alan sailer April 19, 2024, 03:49:28 PM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
Bobakman April 19, 2024, 01:53:57 PM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
MRMILSTAR April 19, 2024, 05:24:19 AM
|
|
Re: Difference between these transformers
[Transformer (Ferrite Core)]
|
Tesla Junior April 19, 2024, 04:24:09 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 19, 2024, 04:20:35 AM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
Bobakman April 19, 2024, 04:05:28 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
alan sailer April 19, 2024, 04:03:54 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 19, 2024, 03:19:19 AM
|
|
Re: IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
davekni April 19, 2024, 03:09:29 AM
|
|
Re: IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
unrealcrafter2 April 19, 2024, 01:47:37 AM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
Bobakman April 19, 2024, 12:19:21 AM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
klugesmith April 18, 2024, 11:33:01 PM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
Bobakman April 18, 2024, 11:15:15 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
davekni April 18, 2024, 10:59:36 PM
|
|
Re: What actually kills MOSFETs?
[Beginners]
|
unrealcrafter2 April 18, 2024, 10:03:48 PM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
klugesmith April 18, 2024, 09:53:25 PM
|
|
Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
|
unrealcrafter2 April 18, 2024, 09:50:09 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 18, 2024, 09:15:55 PM
|
|
Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Mads Barnkob April 18, 2024, 08:50:49 PM
|
|
Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
unrealcrafter2 April 18, 2024, 08:11:27 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
davekni April 18, 2024, 07:28:05 PM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
Bobakman April 18, 2024, 06:30:30 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 18, 2024, 06:03:57 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 18, 2024, 05:26:13 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
NyaaX_X April 18, 2024, 04:03:38 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 18, 2024, 02:56:40 PM
|
|
Re: DIY induction guns? (warning:long)
[Induction Launchers, Coil Guns and Rails guns]
|
Benbmw April 18, 2024, 06:17:15 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 18, 2024, 05:46:07 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
MRMILSTAR April 18, 2024, 05:18:31 AM
|
|
Re: IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
davekni April 18, 2024, 04:34:52 AM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
klugesmith April 18, 2024, 04:11:53 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 18, 2024, 04:02:44 AM
|
|
Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
davekni April 18, 2024, 03:35:52 AM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
MRMILSTAR April 17, 2024, 11:54:05 PM
|
|
100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Benjamin Lockhart April 17, 2024, 11:37:16 PM
|
|
Re: Has anyone tried to build a TMT (extra coil) Tesla coil?
[General Chat]
|
Michelle_ April 17, 2024, 02:29:30 AM
|
|
Re: Has anyone tried to build a TMT (extra coil) Tesla coil?
[General Chat]
|
MRMILSTAR April 16, 2024, 11:56:12 PM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
klugesmith April 16, 2024, 11:46:57 PM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
Bobakman April 16, 2024, 10:40:11 PM
|
|
Has anyone tried to build a TMT (extra coil) Tesla coil?
[General Chat]
|
Michelle_ April 16, 2024, 09:21:39 PM
|
|
Re: Medium Drsstc question
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
flyingperson23 April 16, 2024, 08:04:16 PM
|
|
Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Benjamin Lockhart April 16, 2024, 06:48:05 PM
|
|
Re: Game changing tesla coil secondary winding suggestions
[General Chat]
|
Michelle_ April 16, 2024, 06:18:40 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 16, 2024, 06:14:53 PM
|
|
Re: 3D printed mini-slayer: world's weakest tesla coil
[Solid State Tesla Coils (SSTC)]
|
unrealcrafter2 April 16, 2024, 05:44:44 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
MRMILSTAR April 16, 2024, 03:12:12 PM
|
|
Re: Drsstc voltage spike question
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
unrealcrafter2 April 16, 2024, 02:28:01 PM
|
|
Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Saattvik24 April 16, 2024, 01:56:26 PM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 16, 2024, 06:50:47 AM
|
|
Re: IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Anders Mikkelsen April 16, 2024, 04:57:47 AM
|
|
Re: IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
ethanwu0131 April 16, 2024, 03:40:53 AM
|
|
Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
flyingperson23 April 16, 2024, 01:31:17 AM
|
|
Re: Game changing tesla coil secondary winding suggestions
[General Chat]
|
Michelle_ April 15, 2024, 11:19:52 PM
|
|
3D printed mini-slayer: world's weakest tesla coil
[Solid State Tesla Coils (SSTC)]
|
Michelle_ April 15, 2024, 11:10:19 PM
|
|
Re: Game changing tesla coil secondary winding suggestions
[General Chat]
|
alan sailer April 15, 2024, 11:04:19 PM
|
|
Re: Ignitron trigger drive ideas?
[Capacitor Banks]
|
Twospoons April 15, 2024, 11:02:05 PM
|
|
Re: Game changing tesla coil secondary winding suggestions
[General Chat]
|
Michelle_ April 15, 2024, 10:57:59 PM
|
|
Re: Game changing tesla coil secondary winding suggestions
[General Chat]
|
Michelle_ April 15, 2024, 10:55:46 PM
|
|
Re: Return of Electronics Flea Market in "Silicon Valley"
[Sell / Buy / Trade]
|
klugesmith April 15, 2024, 10:37:32 PM
|
|
Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Saattvik24 April 15, 2024, 10:05:00 PM
|
|
Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
MRMILSTAR April 15, 2024, 09:28:50 PM
|
|
Ignitron trigger drive ideas?
[Capacitor Banks]
|
klugesmith April 15, 2024, 09:06:42 PM
|
|
Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Mads Barnkob April 15, 2024, 08:46:32 PM
|
|
Re: Game changing tesla coil secondary winding suggestions
[General Chat]
|
Benbmw April 15, 2024, 08:38:39 PM
|
|
Re: Game changing tesla coil secondary winding suggestions
[General Chat]
|
sky-guided April 15, 2024, 08:23:40 PM
|
|
How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
|
Bobakman April 15, 2024, 06:43:23 PM
|
|
Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
flyingperson23 April 15, 2024, 06:29:10 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 15, 2024, 05:21:53 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 15, 2024, 05:15:33 AM
|
|
Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
davekni April 15, 2024, 04:07:54 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
davekni April 15, 2024, 03:49:03 AM
|
|
Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
alan sailer April 14, 2024, 09:46:30 PM
|
|
Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
|
Michelle_ April 14, 2024, 07:31:00 PM
|
|
Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Saattvik24 April 14, 2024, 02:26:19 PM
|
|
Re: mg75q2ys40 IGBT
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Mads Barnkob April 14, 2024, 07:20:54 AM
|
|
Re: IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Mads Barnkob April 14, 2024, 07:18:20 AM
|
|
Re: Game changing tesla coil secondary winding suggestions
[General Chat]
|
Michelle_ April 13, 2024, 06:46:40 AM
|
|
Re: Game changing tesla coil secondary winding suggestions
[General Chat]
|
Michelle_ April 13, 2024, 04:18:42 AM
|
|
Re: Upper and Lower Explosive Limits on Confined Flammable Vapors at -79 C.
[General Chat]
|
alan sailer April 13, 2024, 03:24:20 AM
|
|
Re: Game changing tesla coil secondary winding suggestions
[General Chat]
|
alan sailer April 13, 2024, 03:20:46 AM
|
|
Game changing tesla coil secondary winding suggestions
[General Chat]
|
Michelle_ April 13, 2024, 03:13:22 AM
|
|
Re: Capacitor Blowout
[Sell / Buy / Trade]
|
lbattraw April 12, 2024, 09:14:58 PM
|
|
mg75q2ys40 IGBT
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
thedark April 12, 2024, 08:40:18 PM
|
|
Re: UD 2.7 OCD LED stays on, no output during inital test
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
davekni April 12, 2024, 07:20:30 PM
|
|
Re: Mosfet Buffer Stage Questions
[Beginners]
|
davekni April 12, 2024, 07:12:43 PM
|
|
IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
ethanwu0131 April 12, 2024, 04:47:33 PM
|
|
Re: UD 2.7 OCD LED stays on, no output during inital test
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
Admiral Aaron Ravensdale April 12, 2024, 11:43:36 AM
|
|
Mosfet Buffer Stage Questions
[Beginners]
|
Egg April 12, 2024, 12:49:02 AM
|
|
Re: UD 2.7 OCD LED stays on, no output during inital test
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
davekni April 12, 2024, 12:41:16 AM
|
|
Re: Plasma Torid - Class E Self Resonant Dual/Stereo - Plasma Torid Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
|
davekni April 12, 2024, 12:22:41 AM
|
|