Author Topic: MMC layout, 630 or 1600V capacitors?  (Read 9009 times)

Offline AndreiRS

  • High Voltage Experimenter
  • **
  • Posts: 73
  • Karma: +0/-0
    • View Profile
MMC layout, 630 or 1600V capacitors?
« on: March 02, 2018, 04:26:33 PM »
Ok I kinda gave up on the home made capacitors, they are not working.

Found some 630V and 1600V capacitors on a store. I could use 14 0.1 uF 1600V capacitors in series, and 7 strings in parallel. Or I could use 44 2.2uF 630 on a single string. Both would give around 50nF. But one layout is just a big series connection, which sounds a bit bad to me, and the other has parallel connections too. Price would be around the same on both cases.

These caps are not those meant for high pulse, but for 2 seconds I think they could work without exploding.

Offline Mads Barnkob

  • Administrator
  • Executive Board Member
  • *****
  • Posts: 2267
  • Karma: +71/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: MMC layout, 630 or 1600V capacitors?
« Reply #1 on: March 02, 2018, 07:53:43 PM »
You should definitely, of the two choices, go for 14x 0.1 uF 1600V capacitors in series, and 7 strings in parallel.

One long single string of 44 caps could have problems with bad voltage sharing, high combined ESR and low current capability.
https://kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline AndreiRS

  • High Voltage Experimenter
  • **
  • Posts: 73
  • Karma: +0/-0
    • View Profile
Re: MMC layout, 630 or 1600V capacitors?
« Reply #2 on: March 02, 2018, 08:23:10 PM »
Nice, thank you Mads. I will ordem them next month, I just hope they work. They are not those capacitor with big leads, but actually the thin ones.

These, 20 or 25mm.



I was looking for these, but they cost around 10 dollars each. :o



980 dollars is a bit out of my budget. :D

Offline Nijin

  • High Voltage Enthusiast
  • *
  • Posts: 18
  • Karma: +1/-0
    • View Profile
Re: MMC layout, 630 or 1600V capacitors?
« Reply #3 on: March 03, 2018, 06:30:35 PM »
To build a good MMC, you can use 942C capacitor serie from Cornell Dublier or C4AS serie from Kemet. For my DRSSTC I use C4AS 680nF 1200V capacitor, they have a better Irms in 4 pins configuration than 942C.
Everything is a fuse if you pass enough current

Offline Hydron

  • Administrator
  • High Voltage Engineer
  • *****
  • Posts: 487
  • Karma: +25/-0
    • View Profile
Re: MMC layout, 630 or 1600V capacitors?
« Reply #4 on: March 04, 2018, 04:45:38 PM »
Are you planning on using these in a DRSSTC, or a spark-gap coil?

The 942C capacitors mentioned are very good, but are rather expensive and unnecessary for a DRSSTC MMC (which are probably less stressful on the capacitors).

Offline AndreiRS

  • High Voltage Experimenter
  • **
  • Posts: 73
  • Karma: +0/-0
    • View Profile
Re: MMC layout, 630 or 1600V capacitors?
« Reply #5 on: March 04, 2018, 06:46:31 PM »
On a rotary spark gap. I don't have how to buy these ones. Our mail system here is being privatized or something like that, and they are not delivering international stuff in time. I will just go with the cheap ones. :(

Offline Hydron

  • Administrator
  • High Voltage Engineer
  • *****
  • Posts: 487
  • Karma: +25/-0
    • View Profile
Re: MMC layout, 630 or 1600V capacitors?
« Reply #6 on: March 04, 2018, 08:57:51 PM »
Having 7 strings in parallel will help a lot with current capability, even with the cheap ones. You'll just have to try it and see!

When I first ran my DRSSTC I used a horrible MMC made out of 5 different types of capacitor while I waited for the mail to deliver the good ones - it got a little warm but worked well enough to test the coil.

Offline AndreiRS

  • High Voltage Experimenter
  • **
  • Posts: 73
  • Karma: +0/-0
    • View Profile
Re: MMC layout, 630 or 1600V capacitors?
« Reply #7 on: March 04, 2018, 09:37:31 PM »
:D

I don't plan running it for long periods, some 5 seconds "bursts" would be good already.

Offline AndreiRS

  • High Voltage Experimenter
  • **
  • Posts: 73
  • Karma: +0/-0
    • View Profile
Re: MMC layout, 630 or 1600V capacitors?
« Reply #8 on: March 12, 2018, 11:55:20 PM »
Maybe tomorrow I can test it. I got the parts today and already assembled the mmc.


Offline profdc9

  • High Voltage Engineer
  • ****
  • Posts: 262
  • Karma: +14/-0
    • View Profile
Re: MMC layout, 630 or 1600V capacitors?
« Reply #9 on: March 13, 2018, 12:12:20 AM »
Looks good.  What kind of capacitors are those, polypropylene, polyester, or ceramics?

Dan

Offline AndreiRS

  • High Voltage Experimenter
  • **
  • Posts: 73
  • Karma: +0/-0
    • View Profile
Re: MMC layout, 630 or 1600V capacitors?
« Reply #10 on: March 13, 2018, 10:57:27 PM »
Hi Dan, thanks. They are polyester. But I don't know much more than that because I couldn't find the datasheet. It has a logo that is kind of a circle and says HBC.

Offline Mads Barnkob

  • Administrator
  • Executive Board Member
  • *****
  • Posts: 2267
  • Karma: +71/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: MMC layout, 630 or 1600V capacitors?
« Reply #11 on: March 14, 2018, 10:37:09 AM »
I think they are comparable with the old and much used Panasonic capacitors, you can find some in the list here, also with datasheets available: http://kaizerpowerelectronics.dk/theory/good-mmc-capacitors/

You should make a center tapping point at the end of the MMC where all strings have a even length wire to it, like you have it now the two strings closest to the connection point can conduct up to 40% more current than the string furthest away from the connection point. Inductance matching between strings is very important in parallel constructions where current sharing is critical for component temperature rise / life time
https://kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline Hydron

  • Administrator
  • High Voltage Engineer
  • *****
  • Posts: 487
  • Karma: +25/-0
    • View Profile
Re: MMC layout, 630 or 1600V capacitors?
« Reply #12 on: March 14, 2018, 12:18:56 PM »
Hmm, I would have thought that the impedance due to the capacitive reactance would swamp the effect of lead inductance - I'm not sure I agree with Mads on this one and personally wouldn't be concerned with the lead length.

Offline Mads Barnkob

  • Administrator
  • Executive Board Member
  • *****
  • Posts: 2267
  • Karma: +71/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: MMC layout, 630 or 1600V capacitors?
« Reply #13 on: March 14, 2018, 12:44:36 PM »
Hmm, I would have thought that the impedance due to the capacitive reactance would swamp the effect of lead inductance - I'm not sure I agree with Mads on this one and personally wouldn't be concerned with the lead length.

It is not the lead length of the capacitors, but the black wire ring at the end of the MMC that should be remade to have even inductance for all strings.
https://kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline Hydron

  • Administrator
  • High Voltage Engineer
  • *****
  • Posts: 487
  • Karma: +25/-0
    • View Profile
Re: MMC layout, 630 or 1600V capacitors?
« Reply #14 on: March 14, 2018, 05:04:08 PM »
I still think it will have close to zero effect - the black ring will be <1uH which is tiny in comparison to the reactance of the capacitors at TC frequencies. For example at 500kHz (a reasonable guess, if anything on the high side which makes the lead wire effect bigger:

14*0.1uF in series = 7nF, reactance at 500kHz = ~45 ohms per string of caps

With an estimate of 1uH for the black wire(generously large - it's likely a quarter of this or less from the geometry) gives reactance of ~3 ohms @ 500kHz, or less than 10% of the capacitor reactance.

While there will be some effect from different connection points, I don't think it will be enough to change much at all - certainly won't cause enough difference in current to have an effect on current sharing/heating.

Offline AndreiRS

  • High Voltage Experimenter
  • **
  • Posts: 73
  • Karma: +0/-0
    • View Profile
Re: MMC layout, 630 or 1600V capacitors?
« Reply #15 on: March 14, 2018, 11:01:35 PM »
Thanks for the link. If I'm lucky it will be close to the biggest panasonic capacitor on that list.

Hmmmmmmm about the leads. I think it will work that way. But maybe I can save them from premature explosions by changing the layout. Not that difficult to change it. It is already 7pm here, tomorrow I will do some testing.

Offline AndreiRS

  • High Voltage Experimenter
  • **
  • Posts: 73
  • Karma: +0/-0
    • View Profile
Re: MMC layout, 630 or 1600V capacitors?
« Reply #16 on: March 15, 2018, 08:46:13 PM »
lol

Turned it on. Working good for half a second, lots of capacitors get destroyed, turn it off.

Offline Hydron

  • Administrator
  • High Voltage Engineer
  • *****
  • Posts: 487
  • Karma: +25/-0
    • View Profile
Re: MMC layout, 630 or 1600V capacitors?
« Reply #17 on: March 15, 2018, 10:40:03 PM »
Sorry to hear it blew up, but good to hear the 1/2 second was OK! I would recommend trying polypropylene capacitors rather than polyester next time - polypropylene is much better for this use.

Offline AndreiRS

  • High Voltage Experimenter
  • **
  • Posts: 73
  • Karma: +0/-0
    • View Profile
Re: MMC layout, 630 or 1600V capacitors?
« Reply #18 on: March 16, 2018, 12:23:36 AM »
I don't have where to buy them now around here. Maybe in the future. Thanks for the advice. ;)

High Voltage Forum

Re: MMC layout, 630 or 1600V capacitors?
« Reply #18 on: March 16, 2018, 12:23:36 AM »

 


* Recent Topics and Posts

post Re: Big Coil Build Log
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
Today at 05:47:34 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
davekni
Today at 04:45:07 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
Today at 04:18:27 AM
post Push Pull VTTC
[Vacuum Tube Tesla Coils (VTTC)]
janno288
Today at 01:10:08 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 27, 2024, 10:54:52 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 27, 2024, 11:53:42 AM
post Re: OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 05:14:36 AM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:47:48 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:41:59 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 27, 2024, 12:04:34 AM
post Re: Super flat QCW simulation (does this look reasonable?)
[Dual Resonant Solid State Tesla coils (DRSSTC)]
toooldforthis
March 26, 2024, 11:08:14 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 11:07:20 PM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 10:46:29 PM
post OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 26, 2024, 09:03:43 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 08:46:59 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 26, 2024, 05:02:18 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 03:16:03 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 26, 2024, 01:41:49 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 04:48:22 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 26, 2024, 04:16:37 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 26, 2024, 04:16:24 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 26, 2024, 04:13:02 AM
post Re: CM400 Induction Heater
[Electronic Circuits]
davekni
March 26, 2024, 04:00:43 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
davekni
March 26, 2024, 03:19:18 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
thedoc298
March 26, 2024, 01:50:42 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 08:05:02 PM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 25, 2024, 07:41:29 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 06:45:46 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 05:44:25 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 25, 2024, 04:47:17 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 04:27:22 PM
post Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 25, 2024, 03:57:34 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 25, 2024, 02:06:41 PM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 04:43:25 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
davekni
March 25, 2024, 02:39:40 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 12:47:09 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 24, 2024, 07:36:32 PM
post Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
Alberto
March 24, 2024, 07:27:24 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 24, 2024, 04:25:23 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 10:47:35 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 09:30:21 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 04:34:31 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 03:04:25 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 01:38:34 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 04:20:03 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 23, 2024, 12:54:30 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 23, 2024, 12:05:57 AM
post capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 22, 2024, 11:45:03 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 22, 2024, 11:30:09 PM
post Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 22, 2024, 10:20:35 PM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Benbmw
March 22, 2024, 09:21:13 PM
post Re: What actually kills MOSFETs?
[Beginners]
AstRii
March 22, 2024, 03:37:11 PM
post What actually kills MOSFETs?
[Beginners]
FPS
March 22, 2024, 05:09:20 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 22, 2024, 03:57:54 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 22, 2024, 02:59:25 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 06:31:42 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
rikkitikkitavi
March 21, 2024, 03:08:01 PM
post Re: [WTS] IGBT, Ferrite, Capacitors, Tools, PSU, Industrial components and parts
[Sell / Buy / Trade]
Mads Barnkob
March 21, 2024, 01:37:32 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Alberto
March 21, 2024, 11:42:07 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 21, 2024, 04:09:14 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 02:15:31 AM
post My Homemade Structural Analysis X-Ray Machine
[X-ray]
Luca c.
March 21, 2024, 01:35:40 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 20, 2024, 10:40:00 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Mads Barnkob
March 20, 2024, 08:03:41 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Mads Barnkob
March 20, 2024, 07:51:57 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 20, 2024, 10:39:47 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 20, 2024, 04:09:59 AM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 20, 2024, 01:13:23 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
March 20, 2024, 12:45:16 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 20, 2024, 12:30:30 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 11:12:24 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:47:49 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:44:19 PM
post Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 19, 2024, 06:52:09 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 19, 2024, 05:02:44 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
Mads Barnkob
March 19, 2024, 05:01:41 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 04:31:02 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 03:59:54 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 06:41:39 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 19, 2024, 04:05:49 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 18, 2024, 09:08:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 09:07:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
Twospoons
March 18, 2024, 08:57:06 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
MRMILSTAR
March 18, 2024, 03:51:33 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:59:46 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:33:25 PM
post Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 11:02:12 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Twospoons
March 18, 2024, 02:36:11 AM
post Re: Best forum for vacuum tube amplifiers?
[General Chat]
Mads Barnkob
March 17, 2024, 07:42:55 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:15:14 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 05:05:04 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
davekni
March 17, 2024, 04:50:51 AM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Twospoons
March 17, 2024, 04:45:17 AM
post 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:17:51 AM
post Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Terry
March 17, 2024, 01:29:32 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 17, 2024, 12:33:06 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
March 16, 2024, 08:46:20 PM
post Re: Bleeder resistor for MMC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hydron
March 16, 2024, 08:39:24 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hydron
March 16, 2024, 08:21:44 PM
post Best forum for vacuum tube amplifiers?
[General Chat]
yourboi
March 16, 2024, 08:20:13 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal