Author Topic: Reverse engineering a big old American smoke detector  (Read 7058 times)

Offline klugesmith

  • High Voltage Senior
  • *****
  • Posts: 695
  • Karma: +22/-0
    • View Profile
Reverse engineering a big old American smoke detector
« on: March 15, 2020, 09:50:48 PM »
Just noticed the thread about big old Soviet smoke detector, which makes this one seem as safe as baby ducklings.  Told this story yesterday, in almost the same words, on another forum.

Here is an old stock Pyrotronics F5B smoke detector head, similar to the F3/5 head. They are still available for people maintaining old installations, but typically cost well over $100 on ebay.

Ionization-type smoke detectors seem to have started in the 1960's. Preventing fires in industrial & institutional settings easily justified the proliferation of 80 microcurie Am-241 alpha particle sources. Those produce enough air ionization that a cold cathode trigger tube can switch the alarm circuit.

I got the pictured device to turn on a neon lamp, within a few seconds of being exposed to smoke from a smoldering popsicle stick. My circuit is shown below, on the right. The original application uses Base Units (sockets) with resistors and a neon indicator lamp, and if any reader has one I'd love to know the circuit details.

.
These old smoke detectors, just like modern ones with less than 1 uCi of radioisotope, use a reference ionization chamber as the high impedance on top of voltage divider. Cheaper than a many-gigaohm resistor, and it automatically compensates for pressure and temperature and decay of the alpha particle source.

I found out that the internal construction is similar to this unfinished drawing.  The ion chambers in schematic above were rendered accordingly.


It came as a surprise that the larger ionization source, which irradiates the smoky chamber, is directly visible through the window-screened ports. Close enough that energetic alpha particles, not just ions, could be escaping from the enclosure. Let's check with some alpha-viewing fluorescent film, like what's sold for making spinthariscopes.


Set shutter time to 30 s, aperture f/1.4, ISO 12800. Lights off, not completely. Go...


This device could be disassembled without any screwdriving, wrenching, or cutting. 
Not sure if that's a good idea, or a thing to talk about.
Even if it were reassembled and tested as a working smoke detector, good as new, ready to protect lives.

Offline John123

  • High Voltage Engineer
  • ****
  • Posts: 238
  • Karma: +5/-0
  • All the gear, no idea. UK
    • View Profile
Re: Reverse engineering a big old American smoke detector
« Reply #1 on: March 16, 2020, 05:57:16 AM »
Looks quite big in the photo compared to the ones inside modern detectors.

How come they were designed as replaceable parts, do they wear out and become unreliable over time?

Offline johnf

  • High Voltage Technician
  • ***
  • Posts: 192
  • Karma: +6/-0
    • View Profile
Re: Reverse engineering a big old American smoke detector
« Reply #2 on: March 18, 2020, 07:34:09 PM »
I think the part has been made much like tubes were made
in fact that looks like a standard octal tube base with a few pins missing.
this would fit well with early electronics manufacture allowing all to be tested before the detector head was put in

Offline TheMaxii2007

  • High Voltage Enthusiast
  • *
  • Posts: 3
  • Karma: +0/-0
    • View Profile
Re: Reverse engineering a big old American smoke detector
« Reply #3 on: June 02, 2020, 04:19:02 AM »
Hello My old smoke detector Am-241 (72 microcurie )  ;)






« Last Edit: June 02, 2020, 04:32:01 AM by TheMaxii2007 »

Offline klugesmith

  • High Voltage Senior
  • *****
  • Posts: 695
  • Karma: +22/-0
    • View Profile
Re: Reverse engineering a big old American smoke detector
« Reply #4 on: June 04, 2020, 06:30:09 AM »
Welcome to the forum, and thank you for the interesting report.

The sectional drawing you shared is much better than anything I've seen before.
It sure beats measuring parts and drawing things from scratch.
Does the document it came from include details of the circuit in base unit?

Is there a model number and/or date code on your device? 
How come the nominal activity is 72 uCi, vs 80 uCi in my specimens and in the F3/5 model we can read about?

Might as well share a picture I made with alpha-viewing film, to get an idea of relative activity in the outer and inner chamber irradiators, next to a modern sub-1-uCi source.
« Last Edit: June 04, 2020, 06:49:45 AM by klugesmith »

Offline TheMaxii2007

  • High Voltage Enthusiast
  • *
  • Posts: 3
  • Karma: +0/-0
    • View Profile

High Voltage Forum

Re: Reverse engineering a big old American smoke detector
« Reply #5 on: June 06, 2020, 10:44:15 PM »

 


* Recent Topics and Posts

post Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
Today at 05:58:27 AM
post Tesla coil UV eye protection?
[General Chat]
Michelle_
Today at 05:17:22 AM
post Re: Tenebrescent Potassium Iodide
[Solid State Tesla Coils (SSTC)]
alan sailer
Today at 12:39:59 AM
post Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
April 23, 2024, 11:07:41 PM
post Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
April 23, 2024, 10:57:39 PM
post Re: Plasma Torid - Class E Self Resonant Dual/Stereo - Plasma Torid Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
OmGigaTron
April 23, 2024, 09:33:49 PM
post Re: Tenebrescent Potassium Iodide
[Solid State Tesla Coils (SSTC)]
haversin
April 23, 2024, 06:00:42 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 23, 2024, 03:50:49 AM
post Re: Tenebrescent Potassium Iodide
[Solid State Tesla Coils (SSTC)]
alan sailer
April 23, 2024, 03:13:31 AM
post Re: Tenebrescent Potassium Iodide
[Solid State Tesla Coils (SSTC)]
haversin
April 23, 2024, 12:50:40 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 22, 2024, 11:21:06 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 22, 2024, 08:11:00 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 22, 2024, 06:15:30 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
NyaaX_X
April 22, 2024, 05:52:50 PM
post Tenebrescent Potassium Iodide
[Solid State Tesla Coils (SSTC)]
alan sailer
April 22, 2024, 05:52:13 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 22, 2024, 04:31:52 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
NyaaX_X
April 22, 2024, 04:05:34 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
markus
April 22, 2024, 01:02:30 PM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
April 22, 2024, 06:32:35 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 22, 2024, 06:24:10 AM
post M2000NM1 toroid for gdt tesla coil
[General Chat]
thedark
April 22, 2024, 05:13:15 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 22, 2024, 02:25:29 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
alan sailer
April 22, 2024, 02:09:18 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 22, 2024, 12:14:21 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 21, 2024, 09:47:15 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
MRMILSTAR
April 21, 2024, 08:34:02 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 21, 2024, 06:09:57 PM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
April 21, 2024, 06:21:54 AM
post Re: Insulate the secondary of the Tesla coil with a PET plastic bottle
[General Chat]
Michelle_
April 21, 2024, 06:18:30 AM
post Re: Insulate the secondary of the Tesla coil with a PET plastic bottle
[General Chat]
davekni
April 21, 2024, 06:12:31 AM
post Re: Insulate the secondary of the Tesla coil with a PET plastic bottle
[General Chat]
MRMILSTAR
April 21, 2024, 05:19:55 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 21, 2024, 02:29:17 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
alan sailer
April 21, 2024, 01:28:59 AM
post Insulate the secondary of the Tesla coil with a PET plastic bottle
[General Chat]
thedark
April 21, 2024, 01:19:44 AM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
April 21, 2024, 12:55:25 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 20, 2024, 11:25:32 PM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
April 20, 2024, 10:28:26 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
davekni
April 20, 2024, 10:23:28 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 20, 2024, 10:06:44 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
davekni
April 20, 2024, 09:21:55 PM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
April 20, 2024, 09:16:14 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
MRMILSTAR
April 20, 2024, 08:58:40 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 20, 2024, 06:18:26 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 20, 2024, 06:15:26 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
MRMILSTAR
April 20, 2024, 03:45:43 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Benjamin Lockhart
April 20, 2024, 06:33:37 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 20, 2024, 05:45:04 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Benjamin Lockhart
April 20, 2024, 05:34:16 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 20, 2024, 04:50:57 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Benjamin Lockhart
April 20, 2024, 04:03:55 AM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
April 20, 2024, 02:35:56 AM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
Bobakman
April 19, 2024, 09:37:52 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
klugesmith
April 19, 2024, 09:20:10 PM
post Re: Next Gen DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
April 19, 2024, 07:22:26 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 19, 2024, 04:46:36 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
alan sailer
April 19, 2024, 03:49:28 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
Bobakman
April 19, 2024, 01:53:57 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
MRMILSTAR
April 19, 2024, 05:24:19 AM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Tesla Junior
April 19, 2024, 04:24:09 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 19, 2024, 04:20:35 AM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
Bobakman
April 19, 2024, 04:05:28 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
alan sailer
April 19, 2024, 04:03:54 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 19, 2024, 03:19:19 AM
post Re: IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
April 19, 2024, 03:09:29 AM
post Re: IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
unrealcrafter2
April 19, 2024, 01:47:37 AM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
Bobakman
April 19, 2024, 12:19:21 AM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
klugesmith
April 18, 2024, 11:33:01 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
Bobakman
April 18, 2024, 11:15:15 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
davekni
April 18, 2024, 10:59:36 PM
post Re: What actually kills MOSFETs?
[Beginners]
unrealcrafter2
April 18, 2024, 10:03:48 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
klugesmith
April 18, 2024, 09:53:25 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
unrealcrafter2
April 18, 2024, 09:50:09 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 18, 2024, 09:15:55 PM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
April 18, 2024, 08:50:49 PM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
unrealcrafter2
April 18, 2024, 08:11:27 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
davekni
April 18, 2024, 07:28:05 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
Bobakman
April 18, 2024, 06:30:30 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 18, 2024, 06:03:57 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 18, 2024, 05:26:13 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
NyaaX_X
April 18, 2024, 04:03:38 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 18, 2024, 02:56:40 PM
post Re: DIY induction guns? (warning:long)
[Induction Launchers, Coil Guns and Rails guns]
Benbmw
April 18, 2024, 06:17:15 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 18, 2024, 05:46:07 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
MRMILSTAR
April 18, 2024, 05:18:31 AM
post Re: IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
April 18, 2024, 04:34:52 AM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
klugesmith
April 18, 2024, 04:11:53 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 18, 2024, 04:02:44 AM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
April 18, 2024, 03:35:52 AM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
MRMILSTAR
April 17, 2024, 11:54:05 PM
post 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
April 17, 2024, 11:37:16 PM
post Re: Has anyone tried to build a TMT (extra coil) Tesla coil?
[General Chat]
Michelle_
April 17, 2024, 02:29:30 AM
post Re: Has anyone tried to build a TMT (extra coil) Tesla coil?
[General Chat]
MRMILSTAR
April 16, 2024, 11:56:12 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
klugesmith
April 16, 2024, 11:46:57 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
Bobakman
April 16, 2024, 10:40:11 PM
post Has anyone tried to build a TMT (extra coil) Tesla coil?
[General Chat]
Michelle_
April 16, 2024, 09:21:39 PM
post Re: Medium Drsstc question
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
April 16, 2024, 08:04:16 PM
post Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
April 16, 2024, 06:48:05 PM
post Re: Game changing tesla coil secondary winding suggestions
[General Chat]
Michelle_
April 16, 2024, 06:18:40 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 16, 2024, 06:14:53 PM
post Re: 3D printed mini-slayer: world's weakest tesla coil
[Solid State Tesla Coils (SSTC)]
unrealcrafter2
April 16, 2024, 05:44:44 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal