Author Topic: Now building a spark chamber  (Read 2871 times)

Offline pentode

  • High Voltage Enthusiast
  • *
  • Posts: 36
  • Karma: +2/-0
    • View Profile
    • humourous
Now building a spark chamber
« on: April 24, 2019, 05:41:07 PM »
I don't suppose anyone is interested in dated spark chambers but...….
I have started building a circular one using Argon gas.
Circular is much easier to seal to ensure it's gas tight.

10 Aluminium plates 200mm dia spaced at 20mm giving a 180mm high display.
Adjustable 25kV DC across alternate plates, non pulsed.

Non pulsed HV was used in the very early spark chambers but one gets spurious discharges.

If my non pulsed system doesn't work I shall have to spend, spend, spend on scintillators and
photo multiplier tubes, amps and timing extras.
"One small step for man"...
…..because he has Arthritis.
www.retinascope.co.uk

Offline pentode

  • High Voltage Enthusiast
  • *
  • Posts: 36
  • Karma: +2/-0
    • View Profile
    • humourous
Re: Now building a spark chamber
« Reply #1 on: April 27, 2019, 12:56:40 PM »

Here's the 10 aluminium  discs with 20mm nylon spacers and nylon bolts.
Each alternate one to be connected for HV supply.
This is just a mock up to ensure everything fits together.   :)

Plates must be even to each other within about 1% so that's .2mm in this case.

Acrylic enclosure shown to have top and bottom plates attached, gas proof
with valves to supply argon and drain chamber of air.

"One small step for man"...
…..because he has Arthritis.
www.retinascope.co.uk

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1783
  • Karma: +46/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Now building a spark chamber
« Reply #2 on: April 27, 2019, 08:55:23 PM »
You have me following your build process :)

Nothing wrong with dated and old school scientific equipment as they are often the basic principles that more modern and complex equipment is build upon, looking forward to see your results.
https://kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline pentode

  • High Voltage Enthusiast
  • *
  • Posts: 36
  • Karma: +2/-0
    • View Profile
    • humourous
Re: Now building a spark chamber
« Reply #3 on: April 30, 2019, 02:19:21 PM »
I hunted around for some small valves for gas inlet/air outlet.
As the whole rig is only 200mm dia x 250mm high I didn't
wish for large ones, so I bought two model railway engine valves. (60mm high)

Both mounted on the top acrylic plate where the argon gas is not inclined to escape
anyway as it is heavier than air.

The rig will be tilted to one side to fill the chamber, argon pushing the air up
and out.....I hope. :)  If a problem I shall have to  pipe the gas to the bottom of the chamber.

Now how to know when the chamber is full?
I shall use a lighted match burning at the exit valve and when it goes out
I should be nearly there !

Is there a better way?




« Last Edit: April 30, 2019, 02:21:18 PM by pentode »
"One small step for man"...
…..because he has Arthritis.
www.retinascope.co.uk

Offline pentode

  • High Voltage Enthusiast
  • *
  • Posts: 36
  • Karma: +2/-0
    • View Profile
    • humourous
Re: Now building a spark chamber
« Reply #4 on: May 01, 2019, 09:42:26 PM »
Whilst waiting for more parts I built the power supply on the acrylic base mounted under the base. (It will be covered for safety as the voltage will be up to 25kV.  )
Initially the supply will be from a 15kV 30m/a  NST I stripped from an old SGTC I once built.

Nothing unusual in the power supply, just series HV diodes in a bridge with smoothing caps and bleeders wound around a piece of acrylic tube.
I always use nylon bolts, super glued to bases etc  to make cheap stand off HV insulators.

 

"One small step for man"...
…..because he has Arthritis.
www.retinascope.co.uk

Offline pentode

  • High Voltage Enthusiast
  • *
  • Posts: 36
  • Karma: +2/-0
    • View Profile
    • humourous
Re: Now building a spark chamber
« Reply #5 on: May 03, 2019, 09:11:42 AM »
I thought about pressure build up in the chamber as sparking will warm up the Argon gas
and so pressure build up.

To keep an eye on this in a very cheap way I will fit a thin sheet of neoprene
onto a 60mm dia neoprene flat washer.  This will be fitted to the top
acrylic plate with a small hole drilled through it.

In this way any pressure increase or decrease will immediately show as a
depression or bulge in the neoprene. (dotted lines)
It will be interesting to watch this as sparking occurs.
I may put a position sensor on it too.

So I can keep an eye on pressure and cut the HV if too much.





« Last Edit: May 03, 2019, 09:17:56 AM by pentode »
"One small step for man"...
…..because he has Arthritis.
www.retinascope.co.uk

Offline pentode

  • High Voltage Enthusiast
  • *
  • Posts: 36
  • Karma: +2/-0
    • View Profile
    • humourous
Re: Now building a spark chamber
« Reply #6 on: May 05, 2019, 11:13:20 AM »
When a partical passing through my chamber ionises the Argon, ( I hope  ),
the spark created will continue so I need to cut the HV after some
short time. As I am finding, switching 20kV plus HV is rather costly so I will make a short period timer to cut the mains supply to the NST, if I can
detect when a spark has been triggered by a partical and not spurious.


This is all a new ball game for me and the next part of the game is ordering
a small cylinder of Argon and a regulator.
to suit. I think these will fit the bill from Machine Mart who is near to me...……..
  https://www.machinemart.co.uk/p/argon-gas-cylinder

https://www.machinemart.co.uk/p/bottle-regulator-small-gas-bottle/?da=1&TC=GS-010120110&gclid=CjwKCAjwk7rmBRAaEiwAhDGhxAv38k0Mveuq4iDGj-d5h0VlQeo9blAsNy8uW2lPxb7esL1KbnfboRoC6RQQAvD_BwE


Maybe I ought to train up as a gas engineer. ;D
« Last Edit: May 05, 2019, 11:24:17 AM by pentode »
"One small step for man"...
…..because he has Arthritis.
www.retinascope.co.uk

High Voltage Forum

Re: Now building a spark chamber
« Reply #6 on: May 05, 2019, 11:13:20 AM »

 


* Recent Topics and Posts

post Re: Tesla Coil Show Controller Project
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Max
Today at 11:13:18 AM
post Re: repair of Panasonic microwave inverter
[Electronic Circuits]
Weston
Today at 10:08:34 AM
post Re: Horrible waveforms advice--just bad test setup?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
Today at 03:20:42 AM
post Re: repair of Panasonic microwave inverter
[Electronic Circuits]
Twospoons
Today at 03:16:27 AM
post 3kW Cisco Server Supply teardown and help needed
[Electronic Circuits]
Da_Stier
July 23, 2021, 09:23:11 PM
post Re: IGBT question
[Dual Resonant Solid State Tesla coils (DRSSTC)]
thedoc298
July 23, 2021, 08:05:58 PM
post Re: IGBT question
[Dual Resonant Solid State Tesla coils (DRSSTC)]
futurist
July 23, 2021, 07:02:18 PM
post Re: IGBT question
[Dual Resonant Solid State Tesla coils (DRSSTC)]
thedoc298
July 23, 2021, 05:33:57 PM
post Re: Horrible waveforms advice--just bad test setup?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
GKnapp
July 23, 2021, 04:51:37 PM
post Re: Horrible waveforms advice--just bad test setup?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
July 23, 2021, 03:52:46 AM
post Re: IGBT question
[Dual Resonant Solid State Tesla coils (DRSSTC)]
thedoc298
July 22, 2021, 10:59:32 PM
post Re: Horrible waveforms advice--just bad test setup?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
GKnapp
July 22, 2021, 08:50:34 PM
post Re: IGBT question
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
July 22, 2021, 08:47:23 PM
post Help needed - which IGBT module to buy
[Dual Resonant Solid State Tesla coils (DRSSTC)]
thedoc298
July 22, 2021, 07:01:24 PM
post Re: Horrible waveforms advice--just bad test setup?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
July 22, 2021, 06:50:07 AM
post Re: Proper phase lead adjustment at the input
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
July 22, 2021, 06:39:37 AM
post Re: Horrible waveforms advice--just bad test setup?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
July 21, 2021, 07:55:03 PM
post Horrible waveforms advice--just bad test setup?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
GKnapp
July 21, 2021, 06:34:13 PM
post Re: Global shutter synchronized to arcs?
[DSLR]
Uspring
July 21, 2021, 05:10:18 PM
post Re: Tesla Coil Show Controller Project
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
July 21, 2021, 12:42:29 PM
post Re: Proper phase lead adjustment at the input
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Chrisader
July 21, 2021, 08:15:00 AM
post Re: Proper phase lead adjustment at the input
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
July 21, 2021, 04:57:04 AM
post Re: Micro-power continuity checker.
[Electronic Circuits]
davekni
July 21, 2021, 03:50:33 AM
post Re: Skm flyback destroyer 🤗
[Transformer (Ferrite Core)]
oneKone
July 21, 2021, 01:50:19 AM
post Proper phase lead adjustment at the input
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Chrisader
July 20, 2021, 10:06:14 PM
post Re: Micro-power continuity checker.
[Electronic Circuits]
klugesmith
July 20, 2021, 06:24:29 PM
post Micro-power continuity checker.
[Electronic Circuits]
davekni
July 20, 2021, 05:37:36 AM
post Re: Help needed with SSTC. First TC build
[Solid State Tesla Coils (SSTC)]
davekni
July 20, 2021, 05:08:24 AM
post Re: Global shutter synchronized to arcs?
[DSLR]
davekni
July 20, 2021, 04:43:05 AM
post Re: Global shutter synchronized to arcs?
[DSLR]
TMaxElectronics
July 20, 2021, 12:09:36 AM
post Re: Help needed with SSTC. First TC build
[Solid State Tesla Coils (SSTC)]
AstRii
July 19, 2021, 11:13:13 PM
post Another question on CT Feedback
[Solid State Tesla Coils (SSTC)]
Maverikie
July 19, 2021, 08:56:04 PM
post Re: Sync RSG motor problems - help and thoughts needed
[Spark Gap Tesla Coils (SGTC)]
newage
July 19, 2021, 07:09:56 PM
post Re: Global shutter synchronized to arcs?
[DSLR]
klugesmith
July 19, 2021, 06:49:08 PM
post Re: Sync RSG motor problems - help and thoughts needed
[Spark Gap Tesla Coils (SGTC)]
klugesmith
July 19, 2021, 04:39:05 PM
post Global shutter synchronized to arcs?
[DSLR]
davekni
July 19, 2021, 06:32:35 AM
post Re: Sync RSG motor problems - help and thoughts needed
[Spark Gap Tesla Coils (SGTC)]
MRMILSTAR
July 19, 2021, 05:22:51 AM
post Re: Sync RSG motor problems - help and thoughts needed
[Spark Gap Tesla Coils (SGTC)]
newage
July 19, 2021, 04:24:38 AM
post Re: a typical sstc half bridge design, any considerations or tips?
[Solid State Tesla Coils (SSTC)]
eli
July 19, 2021, 12:35:18 AM
post Re: a typical sstc half bridge design, any considerations or tips?
[Solid State Tesla Coils (SSTC)]
Mads Barnkob
July 19, 2021, 12:15:43 AM
post a typical sstc half bridge design, any considerations or tips?
[Solid State Tesla Coils (SSTC)]
eli
July 18, 2021, 11:44:03 PM
post Re: HFSSTC design help and questions
[Solid State Tesla Coils (SSTC)]
eli
July 18, 2021, 09:33:40 PM
post Re: Sync RSG motor problems - help and thoughts needed
[Spark Gap Tesla Coils (SGTC)]
johnf
July 18, 2021, 09:07:15 PM
post Re: Sync RSG motor problems - help and thoughts needed
[Spark Gap Tesla Coils (SGTC)]
MRMILSTAR
July 18, 2021, 03:38:01 PM
post Best and stable version of video
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Transgarp
July 18, 2021, 03:33:31 PM
post Sync RSG motor problems - help and thoughts needed
[Spark Gap Tesla Coils (SGTC)]
newage
July 18, 2021, 01:30:46 PM
post Re: DRSSTC design advise / Primary peak current calculation
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
July 17, 2021, 10:05:39 AM
post Re: DRSSTC design advise / Primary peak current calculation
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
July 16, 2021, 11:01:43 PM
post Re: DRSSTC design advise / Primary peak current calculation
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Martin
July 16, 2021, 09:55:50 AM
post Re: Skm flyback destroyer 🤗
[Transformer (Ferrite Core)]
Patrick
July 16, 2021, 09:54:50 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal